SPXFLOW Seital Separation SE 40CX-Q2P2 страница 4 Скачать руководство пользователя

Страница: 4 / 126

Chapter 1

SEITAL S.r.l.

Rev. 2 of 11/02/98

Page 1-2

Use and maintenance handbook: Centrifugal separator

SE 40CX

1.3.

Handbook index

HANDBOOK USE

1-1

1.1.

OW TO READ THE

ANDBOOK

........................................................................................ 1-1

1.2.

OW TO BRING UP

DATE THE

ANDBOOK

................................................................. 1-1

1.3.

ANDBOOK INDEX

............................................................................................................. 1-2

GENERAL INFORMATION

2-1

2.1.

ANUFACTURER AND MACHINE DATA

............................................................................. 2-1

2.2.

ECHNICAL SERVICE

......................................................................................................... 2-1

2.3.

LOBAL ASPECTS OF SAFETY

........................................................................................... 2-1

2.3.1.

NSTALLATION

................................................................................................................. 2-1

2.3.2.

ARNINGS FOR THE OPERATORS

.................................................................................... 2-1

2.3.3.

AINTENANCE PROGRAMS

............................................................................................. 2-2

2.3.4.

NVOLVED OPERATORS AND TECHNICIANS

..................................................................... 2-2

2.3.5.

AIN WORKING MODES

.................................................................................................. 2-2

2.3.6.

ORESEEABLE ERRORS AND INCORRECT BEHAVIOURS

................................................... 2-3

2.3.7.

IST OF USED SYMBOLS AND WARNINGS

........................................................................ 2-3

2.3.8.

AFETY PRESCRIPTIONS

.................................................................................................. 2-3

2.4.

SED TERMS AND ABBREVIATIONS

................................................................................... 2-6

2.5.

ESPONSIBILITY

................................................................................................................ 2-6

MACHINE DESCRIPTION

3-1

3.1.

ENERAL DESCRIPTION

.................................................................................................... 3-1

3.2.

PERATING PRINCIPLES

.................................................................................................... 3-1

3.3.

ECHNICAL CARD

.............................................................................................................. 3-3

3.4.

OISE LEVEL

...................................................................................................................... 3-4

3.5.

ESTINATION AND FORESEEN PLACE OF USE

................................................................... 3-4

3.6.

MPROPER USES AND CONTRA

INDICATIONS

................................................................... 3-4

LIFTING, TRANSPORT, STORAGE

4-1

4.1.

ACHINE DELIVERY

.......................................................................................................... 4-1

4.2.

ACKING AND UNPACKING

................................................................................................ 4-1

4.3.

IFTING AND TRANSPORT OF THE PACKED MACHINE

..................................................... 4-1

4.4.

IFTING AND TRANSPORT OF THE MACHINE WITHOUT PACKING

.................................. 4-2

4.5.

AREHOUSE STORAGE

...................................................................................................... 4-4

INSTALLATION/PREPARATION TO START

5-1

5.1.

NVIRONMENT

................................................................................................................... 5-1

5.2.

ORKING NECESSARY SPACE

........................................................................................... 5-2

5.3.

QUIPMENT

........................................................................................................................ 5-2

5.4.

OCATION AND ASSEMBLY ON PLACE

.............................................................................. 5-2

5.5.

UBRICATION

..................................................................................................................... 5-3

5.5.1.

EARINGS AND GEARS LUBRICATION

............................................................................. 5-3

5.5.2.

UBRICATION OF THREADS AND CONTACT SURFACES OF THE BOWL PARTS

.................. 5-5

5.6.

YSTEMS CONNECTION

...................................................................................................... 5-5

5.6.1.

LECTRICAL SYSTEM CONNECTION

................................................................................ 5-5

5.6.2.

YDRAULIC CONNECTION FOR OPERATING WATER

........................................................ 5-6

5.6.3.

EPARATOR HYDRAULIC CONNECTION

........................................................................... 5-7

5.6.4.

NEUMATIC SYSTEM CONNECTION

................................................................................. 5-8

BOWL AND INLET-OUTLET FLOW UNIT

6-1

6.1.

OWL ASSEMBLY

............................................................................................................... 6-1

Содержание Seital Separation SE 40CX-Q2P2































































































































Результаты поиска

Содержание Seital Separation SE 40CX-Q2P2

Отзывы:

Похожие инструкции для Seital Separation SE 40CX-Q2P2

Бренды по названию

Популярные бренды

SPXFLOW Seital Separation SE 40CX-Q2P2, Инструкция по эксплуатации

Результаты поиска

Содержание Seital Separation SE 40CX-Q2P2

Отзывы:

Похожие инструкции для Seital Separation SE 40CX-Q2P2

Бренды по названию

Популярные бренды