SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 54

Страница: 54 / 60

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection
Ltd. We reserve the right to alter or amend any published specification without notice.

Page 54 of 59

7.2

Typical Reel Resistances

P343 and G4 Specialist - 150m

/500’ reel

7-Way reel plug

Signal

Slipring PCB

Resistance

/Ohms

2
3

Vid +

Ring 1 (centre)

TBC

Gnd

Ring 4 (outer)

TBC

Vid -

Ring 2

TBC

Gnd

Ring 4 (outer)

TBC

Power +

Ring 3

TBC

Be aware that these values may change if the reel length has been significantly changed or cut
back during service operations!

7.3

Pressure Test

If the following equipment is available, carry
out a pressure test. Whilst this recommended,
it is not essential.

Fit pressure test Jig

09/RP3210Z2 to the end

of the rod.

Содержание Pearpoint Flexiprobe P340





























































Результаты поиска

Содержание Pearpoint Flexiprobe P340

Отзывы:

SPX Pearpoint Flexiprobe P340, Руководство по обслуживанию, Страница: 54 / 60

Результаты поиска

Содержание Pearpoint Flexiprobe P340

Отзывы: