SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 60

SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 27

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation.

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection
Ltd. We reserve the right to alter or amend any published specification without notice.

Page 27 of 59

5.1. RP3181 Rod-End Re-termination Procedure

Examine the full length of the rod for damage, particularly any penetration of the outer sheath or
kinking.

Cut off the old termination including any damaged rod.

Slide the Shroud nut, Taper nut, Thrust washer, Nylon collet (narrow-end towards taper nut), O-
ring washer (with flat surface towards nylon collet, taper side towards O-ring) and the 12mm O-
ring onto the termination end of the rod.

Remove 11mm of the outer
insulation from the rod. Remove
the Kevlar braid.

Trim it as close to the black outer
sheath as possible.

«
...
25
26
27
28
29
...
»

Содержание Pearpoint Flexiprobe P340





























































Отзывы:

Нет отзывов