SPX PE17 Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

SPX PE17 Series Скачать руководство пользователя страница 1

HYDRAULIC PUMP

Max. Capacity: See Pump Data Plate

Definition: A hydraulic pump delivers hydraulic fluid under
pressure through the use of compressed air, an electric motor,
or a gas engine as a power source.

Form No. 102875

Operating Instructions for:

Electric Motor Powered Pumps
Gas Engine Powered Pumps
Rotary Air Motor Powered Pumps

(As listed in EC Declaration)

dB(A) at

Idle and

Pump

kw

700 Bar

PE8 Series

.37

67/81

PE17 Series

.37

67/81

PA17 Series

1.12

85/90

PE30 Series

.74

87/82

PG30 Series

1.49

84/96

PE46 Series

1.12

77/81

PA46 Series

2.24

85/90

PE55 Series

.84

87/86

PA55 Series

2.24

87/88

PG55 Series

2.98

75/87

PR10 Series

.19

65/72

PG18 Series

1.86

81/96

PG120 Series

4.1

85/95

PQ120 Series

2.24

73/78

PG400 Series

14.9

N/A

66262

2.24

N/A

UNIVERSAL

MOTOR

TEFC MOTOR

AIR MOTOR

DC MOTOR

RESERVOIR

GASOLINE

ENGINE

NOTE:

•

For a detailed parts list or to locate a Power Team Authorized
Hydraulic Service Center, contact your nearest Power Team facility.
A list of all Power Team facilities is located at the end of this
document.

•

Carefully inspect the pump upon arrival. The carrier, not the
manufacturer, is responsible for any damage resulting from
shipment.

•

The customer can choose from a variety of motors, controls,
reservoirs, and other options. These instructions will include
directions for options that your particular pump may not have.

•

Do not change motors without consulting the pump manufacturer's
Technical Services Department.

Q U

A R

T E

R

H O

R S

E

®

12 VDC

Sheet No.

1 of 8

Rev 10

Date: 02 Mar 2005

© 2005 SPX Corporation

Tech. Services: (800) 477-8326

Fax: (800) 765-8326

Order Entry: (800) 541-1418

Fax: (800) 288-7031

SPX Corporation
5885 11th Street
Rockford, IL 61109-3699 USA

Internet Address:

http://www.powerteam.com

®

1
2
3
...
»

Содержание PE17 Series

















Отзывы:

Нет отзывов