SPRT SP-POS88V Скачать руководство пользователя страница 16

Страница: 16 / 18

Steps for exiting of parameter setup:

Open paper case cover and press the

【

FEED

】

button; then close paper case

cover and release the

【

FEED

】

button. The printer will save the setup of

parameters, exit setting mode and enter the normal working mode.

The data will not be saved if turn off the printer directly.

2.8 Enter the program upgrade mode

When printer is power off,open paper case cover. Hold the

【

FEED

】

button, then

switch on the printer and release the

【

FEED

】

when the status indicator and

paper-out indicator flash alternately. Then press the

【

FEED

】

for five times and

close the paper cover, printer enter the program upgrade mode. At this time,
the status indicator flash once a second.

Quick enter method:
Open the paper case cover firstly when printer is power off. Hold the

【

FEED

】

button and switch on the printer, then release the

【

FEED

】

button quickly, then

printer enter the program upgrade mode. At this time, the status indicator flash
once a second.

Содержание SP-POS88V



















Результаты поиска

Содержание SP-POS88V

Отзывы:

Похожие инструкции для SP-POS88V

Бренды по названию

Популярные бренды

SPRT SP-POS88V, Руководство пользователя

Результаты поиска

Содержание SP-POS88V

Отзывы:

Похожие инструкции для SP-POS88V

Бренды по названию

Популярные бренды