SPRT SP-EU58III Скачать руководство пользователя страница 13

Страница: 13 / 61

constant on then cycle. The times of flashing means the type of mistake.

Error

Description

The flashing way of [ERROR]
ERROR

Error

The printer can not work normally

after the memory need to be
read-write

Error

The voltage of power is too high

Error

The voltage of power is too low

Error

The CPU execution to the wrong
address

Error

Connection of temperature
detection circuit connection error

5.2 Self-Test

After receiving the printer, user can check its current setup and status at anytime. Self-test way is
as below: Power off, then hold down the

【

FEED

】

button and press the

【

POWER

】

button at

the same time. Then restart the printer.

5.3 Hexadecimal Print

Function of hexadecimal print: printing date received from host machine through hexadecimal
number and its corresponding character and in this way it will be easy to debug the application
Steps to enter hexadecimal printing mode: Power off, open

【

Printer Roller

】

and press the

【

FEED

】

button at the same time,then restart the printer and release the

【

FEED

】

button.

Power on,release the button after light flashing and close the

【

Printer Roller

】

, printer is in the

hex mode.
Steps to withdraw the hex printing mode:turn off power supply or press

【

FEED

】

button three

times.

5.4 Setup of printer parameter

This function is for the setup of parameters.
Steps for setting parameters: Power off, open

【

Printer Roller

】

and press the

【

FEED

】

button

at the same time; release the

【

FEED

】

button after light flashing; then press the

【

FEED

】

twice

and close the

【

Printer Roller

】

; printer is in the parameter setting mode. Print the first parameter

which can be set and its current setup;Details can be seen from appendix.
Steps for exiting of parameter setup: open

【

Printer Roller

】

and press the

【

FEED

】

button;then

close the

【

Printer Roller

】

, release the

【

FEED

】

button and save the setup of parameter and exit;

Содержание SP-EU58III






























































Результаты поиска

Содержание SP-EU58III

Отзывы:

Бренды по названию

Популярные бренды

SPRT SP-EU58III, Руководство пользователя

Результаты поиска

Содержание SP-EU58III

Отзывы:

Бренды по названию

Популярные бренды