background image

GENERAL SAFETY

 

1.

 

Never allow motor to be submerged in any liquid or 

operated while wet. 

2.

 

Never touch unit with wet hands or while standing in 

a wet environment until power is turned off to unit. 

3.

 

Always use a properly grounded power supply to unit. 

4.

 

Use wire/extension cords should be underwriters 

laboratories listed. The proper fuse size should always 

be used.   

5.

 

All wiring should be performed by a qualified 

electrician and follow all electrical and safety codes as 

well as the most recent national electrical code (NEC) 

and the occupational safety and health act (OSHA). 

6.

 

Protect electrical cord from sharp objects, hot 

surfaces, oil, and chemicals. Avoid kinking the cord. 

Replace or repair damaged or worn cords 

immediately. 

7.

 

Disconnect power before servicing unit. If power 

disconnect is out of sights, lock it in the open position 

and tag it to prevent unexpected application of 

power. 

8.

 

Do not touch an operating motor. Modern motors are 

designed to operate at high temperatures. 

9.

 

Never operate unit around explosive fumes or liquids 

or in an explosive atmosphere. 

GROUNDING 

A ground screw is provided on the Liquid Inlet Body 

marked with a ground symbol. A ground wire should be 

clamped under the screw head and connected to earth 

ground via an approved grounding method. Likewise, a 

ground wire should be affixed to the tank and terminated 

at an earth ground.  

DANGER: 

It is not sufficient to ground only the 

tank washer or the tank itself because the 

electrical continuity between the tank wash 

unit and tank cannot be guaranteed. A separate ground 

connection from both the tank wash unit and the tank 

itself should be made. Failure to follow this instruction 

can result in buildup of static charge between the tank 

and the tank washer parts which could cause a sudden 

discharge of current with a resultant explosion or fire. 

 

You may be killed or seriously injured if you do not 

follow these instructions. 

HIGH IMPACT SPRAYS 

This tank washer may be equipped with solid stream 

nozzles which concentrate the flow energy into a small 

area for maximum impact and cleaning efficiency. 

Operation at high pressure increases their effectiveness 

but also creates a hazard if the proper precautions are 

not followed. 

WARNING: 

INJURY HAZARD FROM  

HIGH IMPACT SPRAYS.

 

High impact sprays can cause severe injury. The liquid 

pressure to the tank washer should never be turned on 

while the unit is outside the tank. 

Failure to follow this 

instruction can result in fluid penetration through 

clothing and into the human skin causing severe injury, 

possibly resulting in amputation or death

. If any part of 

the body comes in contact with the spray stream, 

immediately consult a physician. 

OPERATION PRECAUTIONS 

It is your responsibly to operate this product at 

recommended speeds, loads and temperatures. 

Run the unit within the specified pressures and flow 

rates for the liquid and air motor to ensure safety. To 

maintain proper operations do not run the unit dry, 

always keep liquid flow on before stopping the air motor. 

DANGER

:

 

DO NOT USE TO SPRAY FLAMMABLE 

LIQUIDS--SUCH USE COULD RESULT IN FIRE OR 

EXPLOSION CAUSING BODILY INJURY OR DEATH.

 

Sound level from motor may exceed 85db(A). Check 

compatibility of service fluid with materials used to 

construct this product. Use a pressure gauge to monitor 

liquid pressure (see 290E-EP-1 for flow rate data). Ensure 

that the pumping system has monitor controls and 

emergency shut off system in case of pressure spike 

which can cause harm to this product. Failure to follow 

this instruction can result in burns, eye injury or other 

serious injury.

 

 

Содержание TankJet AA290E-EP Series













Отзывы: