background image

REMOVING BATTERY INSULATOR TAB

INTRODUCTION

SNAPSHOT

 

PEDOMETER

USER GUIDE

/INSTRUCTION MANUAL

Congratulations on your purchase of a Sportline SnapShot Pedometer. The Snap-

Shot Pedometer features a highly advanced pedometer technology that accurately 

measures your body movements when worn from multiple locations on the body 

and in multiple orientations.

Please keep in mind your pedometer is a sensitive technical instrument. With 

proper care and maintenance, it will last for many years. However, improper care 

and handling can cause the various sensors to be damaged and to stop function-

ing.

HOW TO USE THIS MANUAL

Please read all sections of this manual carefully and become fully familiar with 

the operation of the pedometer before using it in the field. Proper setup and op-

eration will greatly enhance the pedometer’s usefulness and your enjoyment. The 

steps for the programming or operation are adjacent to the screen illustration. 

Key points and important information are shown in highlighted blocks.

CUSTOMER SUPPORT

If you have questions, comments or need assistance with your Sportline Snapshot 

Pedometer, you may contact Customer Support by calling 

1-866-694-4575

.

NOTE:

 In order to activate your pedometer after purchase, you must remove the 

battery insulator tab inside the battery compartment.  

1.

  Slide the battery compartment cover toward the bottom edge of the unit.  

2.

  Remove the tab and be sure that the battery is in the correct polarity position 

(positive (+) side of the battery is visible). 

3.

  Replace the battery compartment cover and fasten by sliding back into place 

(NOTE: cover will “click” into place and automatically seal).

4.

  Remove the label that appears on the pedometer display.

1

2

3

SNAPSHOT

 

PEDOMETER

www.sportline.com

www.sportline.com

Sportline® is a trademark of SPORTLINE, a division
of EB Sport Group, Yonkers, NY 10701
Distributed in the UK by
EB Brands (UK), Worcester, WR4 9FA
All Rights Reserved. ©2011
SPXXXXXXXROD

PROGRAMMING THE PEDOMETER

4.

  Adjust Height by 

PRESSING

 the 

+

 or 

-

 keys. 

PRESS

 the 

SET

 key to accept value. 

The unit will automatically calculate your Stride Length.

5.

 

PRESS

 the 

SET

 key to accept this value or you can adjust your Stride Length 

(see “Determining Stride Length” in far right panel) by 

PRESSING

 the 

+

 or 

-

 

keys. 

6.

 

PRESS

 the 

SET

 key. The unit is now programmed and ready for use!

4

5

6

PROGRAMMING THE PEDOMETER

In order to ensure exercise data is as accurate as possible, you must complete the 

following steps to enter your personal profile:

1.  

Enter the Programming Sequence by 

PRESSING & HOLDING

 the 

SET

 key on the 

back of the unit for approximately 3 seconds. 

2. 

Select unit of measure (metric or imperial) by 

PRESSING

 the 

+

 or 

-

 keys on the 

back of the unit.

 PRESS

 the 

SET

 key again. 

3.  

Adjust Weight (in pounds or kilgrams) by 

PRESSING

 the 

+

 (to increase) or 

-

 (to 

decrease) keys.  

PRESS

 the 

SET

 key to accept value and advance to set Height.

1

2

3

To adjust value: 

PRESS + OR -

To accept and advance: 

PRESS SET

OPERATING/RESETTING THE PEDOMETER

OPERATING THE PEDOMETER

The SnapShot Pedometer automatically begins capturing data once movement  

occurs.  There are no Start or Stop buttons to push.

TO CLEAR ALL CURRENT PEDOMETER DATA:
1.

  Press & Hold the RESET key on the front of the unit.  

2. 

Continue holding as the display reads “RESET”. 

3.

  When pedometer data reads zeros (O), release the RESET key. The unit is now 

ready for a new workout.

 

NOTE: 

Your personal profile settings will be saved. 

3

2

1

Отзывы:

Похожие инструкции для SnapShot Pedometer