Splicecom 4100 Скачать руководство пользователя страница 58

Страница: 58 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

Select Update or Apply to save the changes.

Please note the WebSetnet feature in Manager Assist will only operate if the handset(s) is using the

default login password.

Viewing the IP address of the PCS 58x/57x/56x/55x

To determine the IP address of a PCS 55x/57x/56x select the Favourites button

, then Settings and then

Phone Information (alternatively press the key at the bottom right hand side and then select Phone

Information). The IP address will be displayed at the top of the screen.

To determine the IP address of the PCS 58x press the Settings icon

five times. The IP address will be

displayed at the top of the Phone Information screen.

Viewing the IP address of a PCS 542

To determine the IP address of a PCS 542 select the Settings button button, press the Down arrow
to highlight Phone Info and then press Accept

. The handset’s IP address will be displayed at the top

of the screen.

Viewing the IP addresses via Manager Assist

A list of the IP addresses for each PCS 542

55x/57x/56x/58x can be viewed in Manager Assist by

selecting System Utilities and then IP Addresses.

Setting the IP Address and Network Configuration

When powering up a PCS 542/55x/56x/57x/58x for the first time a DHCP server is required to give the PCS

IP Phone an IP address and its network configuration. The handset can continue to use DHCP or can be

given a static IP address and networkconfiguration as follows:

Via Manager Assist
Firstly, note that this facility will only be available if the handset(s) concerned is using the default login

password.

From Manager Assist select Configuration Aids, and then under the System group select

WebSetnet.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды