Splicecom 4100 Скачать руководство пользователя страница 292

Страница: 292 / 374

Installation and Maintenance Manual

Maintenance & Troubleshooting

288

Installation and Maintenance Manual v4/0615/10

Reboot locally:

Perform an orderly shut down of the Call Server by pressing the Reset Switch once. The SpliceCom

LED will slowly flash when the shut down is complete.

Press the Reset Switch once to restart the Call Server or wait for the Call Server to automatically

reboot and the patch will be sent to the Call Server.

Reboot remotely:

Telnet on to the Call Server via Root (as described in the Root Access to a Call Server section from page

272) and enter

poweroff

to reboot the Call Server.

Please note - if you are performing a root upgrade a second reboot may be required.

The patch will be automatically deleted from the ftp directory if the file has been accepted.

Upgrading a 5100/5108 Call Server/NSG

The relevant new software patch must be sent to the Call Server as described above. If you have

extracted the software via Telnet then reboot the Call Server. If you extracted the software via a reboot,

the Call Server will be automatically upgraded during the reboot.

The current version of software being used by the Call Server can be viewed in Manager by selecting

Modules, then the relevant module. The Product Version field will display the version number being

used.

Upgrading the 5100 Call Server and NSG via the USB port

A USB memory stick can be used to upgrade the software on a 5100 Call Server.

Place the cs5100.root.tar.gz or cs5100.patch.tar.gz files on to the memory stick

Put the memory stick into the USB port on the front of the 5100 Call Server

Reboot the Call Server and the software will be upgraded.

Please note: An upgrade will take place on each reboot of the Call Server if the memory stick is left in the

USB port.

Upgrading an Intelligent Gateway Module

The new software for an Intelligent Gateway Module (IGM) is supplied as eg igm.4.0.66.tar.gz. Rename

this file to igm.tar.gz and send this new software patch to the Call Server as described in the Send a

Software Patch to the S8000/S716/5100/5108/NSG Call Server section from page 287 before proceeding.

Once the software patch has been sent to the Call Server, the software on the IGM can be upgraded, as

follows.

Within any browser enter the IP address of the IGM to open the configuration web pages.

Within the Password: field enter the password for the IGM, by default this will be 7388.

Select the Login button.

Click on the Upgrade Unit button.

In the window displayed enter the Diagnostic Engineering Password for the system.

If the software file is found in the tftp directory a message confirming the transfer will be

displayed.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды