manualshive.com logo in svg

Splicecom 4100, Инструкция по установке и обслуживанию

Kestrel 4100 - Компактный и точный прибор для измерения погодных условий. Получите бесплатное руководство по эксплуатации с инструкцией по быстрому старту. Скачать его с manualshive.com и начать использование сразу. Необходимый инструмент для путешественников и любителей спорта на открытом воздухе.

Поделиться
Скачать
background image

Installation and Maintenance Manual

 

 

 

Configuring system functionality 

Installation and Maintenance Manual v4/0615/10 

 

197 

 

= (equal sign)  Will record all calls received on this number.  Please refer to the Call Recording section 

from page 256 for further information. 

~ (tilde) 

Will bypass any compression (required for fax calls) 

 

Please note that these options may cause the outbound CLI to fail therefore double entries will be 

required. 

 

Outgoing CLI for external calls 

A DDI Plan entry is also used when external calls are made by a User.  If the extension number making 

the call is found in the Translate To field of a DDI Plan entry the number in the Number Match field will be 

used as the outgoing CLI. (Please note if 

the User’s Dial Plan contains an entry specifying the outgoing 

CLI this will take precedence (please refer to page 134 for further details).)  If no matches are found then 

the Trunk’

s Presentation Number will be used. 

 

The order in which the configuration of the system will determine the outgoing CLI to be presented for a 

specific User when making an external call is as follows: 

1

 

Dial Plan entry 

–

 Translate CLI To field 

2

 

DDI Call Plan entry 

3

 

Trunk 

–

 Presentation Number field 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

User dial

s from extension “x”

 

Digits dialled are matched by a 
Dial Plan entry 

Extension number “y” found in 

Translate CLI To field of the Dial 
Plan entry 

Extension number “y” matched 

in DDI Plan entry 

DDI number in Number Match 

field of DDI Plan entry sent as 
CLI 

Yes 

Yes 

Extension number “x” 

matched in DDI Plan entry 

DDI number in Number Match 

field of DDI Plan entry sent as 
CLI 

Yes 

No 

No 

Trunk Presentation 

Number sent as CLI 

No 

Содержание 4100























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4100

D-Link ShareCenter Pro DNS-1200-05 Quick Installation Manual preview
ShareCenter Pro DNS-1200-05
Бренд: D-Link Страницы: 68
IBM BladeCenter HS21 1885 Problem Determination And Service Manual preview
BladeCenter HS21 1885
Бренд: IBM Страницы: 140
Buffalo LPV4-U2-300S Quick Setup Manual preview
LPV4-U2-300S
Бренд: Buffalo Страницы: 2
MSI MS-S0081 Manual preview
MS-S0081
Бренд: MSI Страницы: 54
MSI E7210 Master-FARM User Manual preview
E7210 Master-FARM
Бренд: MSI Страницы: 34
Zonet ZPS3611 - QUICK Quick Installation Manual preview
ZPS3611 - QUICK
Бренд: Zonet Страницы: 1
Fujitsu PRIMERGY Econel 230R S1 Service Supplement Manual preview
PRIMERGY Econel 230R S1
Бренд: Fujitsu Страницы: 53
Fujitsu Primergy ECONEL 100 S2 Start Manual preview
Primergy ECONEL 100 S2
Бренд: Fujitsu Страницы: 8
Fujitsu PRIMERGY Econel 200 S2 Options Manual preview
PRIMERGY Econel 200 S2
Бренд: Fujitsu Страницы: 65
Fujitsu PRIMERGY MX130 S1 Operating Manual preview
PRIMERGY MX130 S1
Бренд: Fujitsu Страницы: 85
Fujitsu PRIMERGY Econel 100 Operating Manual preview
PRIMERGY Econel 100
Бренд: Fujitsu Страницы: 64
Fujitsu primergy h250 Manual preview
primergy h250
Бренд: Fujitsu Страницы: 105
Fujitsu Primergy N800 Manual preview
Primergy N800
Бренд: Fujitsu Страницы: 142
Fujitsu PRIMERGY GX2460 M1 Upgrade And Maintenance Manual preview
PRIMERGY GX2460 M1
Бренд: Fujitsu Страницы: 251
Fujitsu PRIMERGY MX130 S2 Upgrade and maintenance manua Upgrade And Maintenance Manual preview
PRIMERGY MX130 S2 Upgrade and maintenance manua
Бренд: Fujitsu Страницы: 256
Fujitsu Primergy RX100 S2 User Manual preview
Primergy RX100 S2
Бренд: Fujitsu Страницы: 275
Fujitsu Primergy RX100 S3 User Manual preview
Primergy RX100 S3
Бренд: Fujitsu Страницы: 287
Fujitsu PRIMERGY ECONEL30 Configuration Manual preview
PRIMERGY ECONEL30
Бренд: Fujitsu Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды