Splicecom 4100 Скачать руководство пользователя страница 17

Страница: 17 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

The DHCP Start Address and DHCP End Address fields specify the range of IP addresses to be given

out when the DHCP Server Mode is set to Enable. (Please note that these fields are irrelevant if the

DHCP Server Mode is set to Disabled.)

The DHCP Base Address specifies the network on which the Call Server will be allocating IP

addresses (default = 192.168.0.0). If DHCP is disabled this must be configured to match the

network that the Call Server is on.

The DHCP Base Mask specifies the subnet mask to be used by the Call Server and if the DHCP

Server Mode is set to Enable this is subnet mask given out. If DHCP is disabled this must be

configured to match the network that the Call Server is on.

The DHCP Router field specifies the default gateway IP address to be used by the Call Server, and if

the DHCP Server mode is set to Enable this will be the Default Gateway address given out.

Select Update or Apply when ready.

Reboot the Call Server (please refer to page 283 for information on how to reboot a Call Server.)

Please note:

When using the default configuration, 192.168.0.250 will be the first IP address to be given out,

followed by 192.168.0.249 etc.

On initial connection a PCS 58x, 57x, 56x, 55x, 410, 400 and 100 will obtain its IP address from a DHCP

server.

On initial connection a Phone Module will obtain its IP address from a DHCP server.

If the DHCP Server Mode is set to Client and the Call Server is unable find a DHCP server on reboot

the SpliceCom LED will turn on for 5 seconds then off for 5 seconds continually until a DHCP server is

found.

Using Auto Add Phones

This feature determines whether phones (analogue or IP) will be able to automatically register with the

system. If turned on (default), each Phone Module and IP Phone will be able to automatically register on

the relevant Call Server, each port and phone will be listed in the configuration and a User automatically

created. If turned off, each Phone Module and IP Phone must be manually registered on the system.

Turn On/Off Auto Add Phones

In Manager, select Modules

Select the Call Server required

Select the Call Server page.

In the Auto Add Phones check box tick to turn on or untick to turn off this feature.

Please refer to the Connecting a Phone Module section from page 39 and the Connecting a PCS IP Phone

section from page 51 for further details.

System Time

The System configuration form displays the current date and time used by the system. This setting can be

changed as follows:

In Manager Assist, select System Utilities then Set Time

Enter the date and time required

Select Update when ready.

This information will be sent and updated on all handsets on the system

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды