Spirent TestCenter страница 15 Скачать руководство пользователя

Страница: 15 / 86

Getting Started

Procedure 1: Check System Requirements

Getting Started with Spirent TestCenter

Procedure 1: Check System Requirements

Review system requirements carefully to ensure successful installation and operation.
System requirements are included in the

Release Notes

document.

Release notes are available as a Related Resource, for each software download, on the
Spirent Customer Service website on the

Downloads

page.

Refer to the readme titled

Spirent TestCenter Release Notes and New Feature Information

for detailed instructions on how to locate the release notes for your version of the
software.

Tip:

Additional system requirements may be included in the release notes provided for

the extended applications that run on Spirent TestCenter.

Содержание TestCenter























































































Результаты поиска

Содержание TestCenter

Отзывы:

Похожие инструкции для TestCenter

Бренды по названию

Популярные бренды

Spirent TestCenter, Начало работы с

Результаты поиска

Содержание TestCenter

Отзывы:

Похожие инструкции для TestCenter

Бренды по названию

Популярные бренды