Congratulations! You are the proud owner of the AIR HOGS
®
Motocross Bike. Your AIR HOGS
®
Motocross Bike can travel
distances of up to 120 feet and race at scale speeds of up to
150MPH (1:9 Scale). Your bike is also equipped with a
wheelie bar, so you can perform pop-a-wheelies!
PLEASE READ THESE INSTRUCTIONS BEFORE USE!
PROBLEMS? PLEASE DO NOT TAKE YOUR
AIR HOGS
®
MOTOCROSS BIKE BACK TO THE STORE!
CALL SPIN MASTER TOLL FREE AT:
1-800-622-8339
IMPORTANT
A. SELECTING YOUR LOCATION:
The Air Hogs
®
Motocross Bike performs best on
FLAT SMOOTH SURFACES, free of bumps and other
obstructions. Do not play on harsh or rocky surfaces.
Do not play on or near roadways. Always consult
your guardian before playing to ensure the area in
which you would like to play is clear and safe!
B. PRESSURING THE ENGINE:
1.
BEFORE PUMPING, ROTATE THE REAR TIRE UNTIL
THE PISTON IS SET AT THE FRONT OF THE PISTON
WINDOW (see CORRECT drawing).
IF THE PISTON IS AT THE BACK OF THE PISTON
WINDOW, THE AIR WILL LEAK OUT OF THE BIKE
DURING PUMPING! (see INCORRECT drawing).
2. Attach the bike to the pump, as shown (a).
3. Lay bike on its side, as shown (b).
4. Place one foot on each side of the pump base and
grasp the pump handle with both hands (b).
5. Pump air into the bike.
6. Push button to unlock pump clip and remove bike from pump.
®
IMPORTANT:
It will take 25 pumps to pressurize your bike. Pull the pump
handle ALL THE WAY up and push it ALL THE WAY down to complete
each of the 25 pumps. Incorrect pumping will result in lower than expected
performance. FOR SAFE USE, DO NOT EXCEED 25 PUMPS.
a
C. STARTING YOUR BIKE:
1. Set the bike on a long flat
surface.
2. Straighten the front and
rear wheels.
3. Give the bike a firm push
forward and continue to
guide the bike on a straight
path for 1-2 feet before
releasing. (c).
IMPORTANT:
It is important to guide the bike on a straight path for
1-2 feet after the engine starts. This is to stabilize the bike and continue it
on a straight course.
c
D. PERFORMING A
POP-A-WHEELIE:
1. Pressurize your bike’s engine, as explained
in section B.
2. Lower the wheelie bar into place, as shown (d).
d
e
f
Troubleshooting Guide:
Problem
1. Cannot pump bike.
2. Engine will not start.
3. Bike will not go straight.
4. Bike will not perform a
pop-a-wheelie.
Cause
1. Air intake on bike and/or
pump nozzle is clogged.
2A. No air in bike.
2B. Did not push bike along
ground to start engine.
2C. Piston is at the back of the
window. in this position, the air
will leak out of the toy and the
engine will not start.
3A. Wheels are turned.
3B. You are not guiding
the bike for 1-2 feet before
releasing.
4. Wheelie bar is not down.
Solution
1. Use a toothpick to gently clean
dirt/foreign material out of the air
intake/pump nozzle.
2A. Pump up bike as detailed in
section B above.
2B. Give bike a firm push along the
ground to start the engine.
2C.Rotate rear tire until piston
moves to the front of the window.
3A. Be sure to straighten the front
and rear wheels before releasing
the bike.
3B. Be sure to guide the bike with
your hand for 1-2 feet before
releasing, as explained in C3 above.
4. Lower wheelie bar into position
as explained in D2 above.
AIR HOGS® is a registered trademark of Spin Master Toys™.
All rights reserved.
AIR HOGS® MOTOCROSS BIKE © 2002 Spin Master Toys.
All rights reserved.
43020 ENG REV 1
Spin Master Toys,
450 Front Street West, Toronto,
Ontario, Canada M5V 1B6
Telephone: 1-800-622-8339
Website: www.spinmaster.com
Email: [email protected]
MOTOCROSS
b
PUMP
CLIP
TIP:
If you are having trouble making the bike go straight without
falling over, try using the wheelie bar. The wheelie bar helps to
balance the bike. This is similar to training wheels on a bicycle.
Note: With practice, your runs will become straighter and longer
and you will no longer need the assistance of the wheelie bar.
3. Place the bike on a
smooth flat surface.
4. Raise the front end of
the bike into the air so
that only the rear
wheel and the wheelie
bar are resting on the
ground (e).
5.Give your bike a firm
push in the direction
you want to go,
remembering to guide
the bike with your
hand for1-2 feet before
releasing,as explained
above (f).
INCORRECT
PISTON
AT BACK
CORRECT
PISTON
AT FRONT
PISTON
PISTON
