Spencer Carrera Tec, Руководство пользователя, Страница: 14 / 22

9
Feature Dimension
Length (mm) 1970
Width (mm) 570
Low High XL XL nn / TEC nn
Loading trolley underwheel height (cm) 50 60 75 nn
Wheel diameter (mm) Ø 200±5%
Load capacity (kg) 170 kg (250kg MAX models)
Weight without standard accessories (kg) TEC TEC TH XL PRO ACTIV
38 39 42 37 40
9. COMMISSIONING
For first use, check that:
•
Packaging is intact and has protected the device during transportation
•
Check that all parts included in the packing list are present
•
General functionality of the device
•
The medical vehicle is equipped with a Spencer fixing system dedicated to the stretcher
•
The stretcher floor is properly levelled
•
The stretcher floor is wide and long enough to accommodate the stretcher and its accessories without becoming an obstacle
•
The wheel of the front leg is at least 5 cm from the ground during vehicle loading and unloading procedures in order to allow for the safe
opening and locking of the front leg - see image in point 11.6
•
The fastenings must keep the stretcher attached to the structure of the vehicle
Do not modify the stretcher structural, leverage or traction parts in any way as this could cause damage to the patient and/or the rescuers.
Failure to take the above measures will preclude safe use of the device, resulting in risk of damage to the patient, operators and the
device itself.
To facilitate insertion of the stretcher into the ambulance, eliminate sharp edges on the edge of the ambulance loading floor. The stretcher
should be secured using Spencer hooks in such a way as to prevent any movement during transport in the ambulance, even in difficult driving
conditions. Practice with a stretcher without a patient before putting the device into service.
For subsequent use, perform the operations specified in paragraph 12.
If the above conditions are met, the device may be considered ready for use; otherwise, you must immediately remove the device from
service and contact the Manufacturer.
Do not alter or modify the device arbitrarily, as doing so could result in unpredictable operation and damage to the patient or rescuers and
will void the warranty and release the Manufacturer from all liability.
Carrera stretchers are available in various heights to be assessed before purchase in relation to the loading configuration on the vehicle.
NOTE: Please contact the manufacturer for installations requiring the use of accessories.
The type of stretcher should be chosen taking into account that, in simulated loading conditions and with the loading trolley on the
ambulance floor, the wheels of the front legs should be 5/6 cm off the ground.
After checking that the stretcher in your possession is suitable for the intended vehicle, you can proceed, if necessary, with adjusting the
coupling parts with the fixing system.
Fastening used
R-MAX / S-MAX / Sensor Lock
CAUTION : Spencer stretcher factory adjustments are already suitable for use with the R-MAX and S-MAX fixing systems. The following
adjustments may only be necessary if the height of the loading trolley has changed when accessories are retrofitted, when the stretcher and
mounting system are ordered separately or if, for any reason, there is an excessive gap between the stretcher and the fixing system.
Unlock the fifth wheel by slightly loosening the frame fixing screws on both sides of the stretcher.
Loosen the screws on the wheels mounted on either side of the fifth wheel in the same way.
See image P6
Adjustment: Push the stretcher so that it is flush with the front of the fixing system.
Push the fifth wheel assembly so that the rear locking system underneath the fifth wheel comes into contact with the rear part of the fixing
system and with the stopper on the R-MAX fastenings.
Insert a shim of about 1cm between the fifth wheel and the rear part of the fastening and check that it has reached a horizontal position.
While holding this position, re-tighten the screws that were previously loosened and check that the fifth wheel is fully locked.
Check that the wheels rest on the ambulance floor and, keeping the shim between the fifth wheel and the fastening, tighten the wheel fixing
screws.
Remove the shim and check that the gap between the stretcher and the fixing system is no more than 5 mm at the front and rear.