manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 89

Unit Serial Number:

 

NOTE:

 

When the programming is complete, record these settings for 

future reference.

Page E-6 

LiQuilaz II E and S Operations Manual

Appendix E Configuring for Ethernet

TCP/IP Settings for the LiQuilaz II Liquid Particle Counter 

Date

Software Version

Set By

MAC Address

IP Address

Multicast Address

Net Mask Address

Gateway Address

:

Viewing Configuration Settings

Type 

sta

(

tus

) and press the 

Enter

 key to display the LiQuilaz II Liquid Particle 

Counter’s configuration settings, software version, and connection status.

If this command does not produce any kind of activity on the display screen:

•

the terminal emulator may be set up incorrectly, or

•

the cable may be improperly connected or faulty

Connecting the Ethernet Cable

The LiQuilaz II Liquid Particle Counter communicates with Facility Net or third party 
Modbus application by means of a CAT 5 UTP Ethernet cable. The sensor is designed to 
work best with a CAT 5 UTP cable. Other types of Ethernet cable may produce excess 
noise. An Information Systems Manager, Network Administrator, or other appropriate 
computer support personnel may be able to assist in procuring a cable or fabricating a 
custom-length cable.

When connecting the LiQuilaz II Liquid Particle Counter to a network, Facility Net will 
find the sensor on the network utilizing the Multicast Address and UDP. Based on your 
configuration, refer to the 

Facility Net Operations Manual

.

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды