manualshive.com logo in svg

Spectris Particle Measuring Systems LiQuilaz II E, Руководство по эксплуатации

Поделиться
Скачать
Spectris Particle Measuring Systems LiQuilaz II E Скачать руководство пользователя страница 76

Appendix D Ethernet Communications Overview

LiQuilaz II E and S Operations Manual

Page D-3

When a Particle Measuring Systems instrument is set to default parameter or factory 
defaults, the network mask is set to 

255.0.0.0

. This corresponds with the 

10.X.X.X

 

address which is also set. 

For large systems, IT personnel will dictate a network mask value and the value may 
be different from what is shown in the table. Make sure the network mask is set as 
specified by IT. All PCs, routers and instruments on a network must use exactly the 
same network mask, or communication problems will arise.

Gateway Address

The gateway address is a special address used to allow communications outside of the 
local network. In the telephone analogy, it allows placing long distance calls. In many 
(if not most) situations, a gateway address is not required.

The default gateway address set when restoring defaults to a Particle Measuring 
Systems instrument is 

10.255.0.60

. This address should be cleared or set to whatever 

is required by IT.

Multicast Address

The multicast address is used by Facility Net to query all instruments attached to a 
local network. The valid multicast address range is defined as 

224.0.0.0

 to 

239.255.255.255

. From a practical standpoint addresses in the 

224.0.X.X

 range 

should not be used as many of them are reserved for other communications.

Particle Measuring Systems assigns a factory default multicast address of 

224.100.100.1

 to all instruments. This address generally does not need to be changed. 

The exception is when sensors are integrated into a large network. In this situation, IT 
may recommend an alternative multicast address to avoid network conflicts.

 MAC Address

All Ethernet devices have a MAC (Media Access Control) address. This address may be 
thought of as an Ethernet serial number. It is unique for all devices. If an instrument 
needs to be replaced with a different instrument for either calibration or service, the 
service technician will duplicate the old instrument’s IP address into the new 
instrument. However, the MAC address of the new instrument will be unique. 

In Particle Measuring Systems instruments the MAC address is set during production. 
The value is permanently stored in non-volatile memory on the main processor circuit 
board. (The MAC address will change if the main circuit board is replaced.) The MAC 
address may be displayed via the HyperTerminal

®

 (i.e., RS-232 service interface) by 

using the 

status

 command. 

Routers and switches keep track of which MAC address is attached where. For that 
reason, it is important for the instrument to tell a router or switch who is attached. For 
all Particle Measuring Systems instruments, this is done at least once when the 

Содержание Particle Measuring Systems LiQuilaz II E














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды