Spectracom VelaSync 1225 страница 73 Скачать руководство пользователя | Manualshive

Страница: 73 / 272

background image

Note:

When compiling the MIB files, some SNMP Manager pro-

grams may require the MIB files to be named something other
than the current names for the files. The MIB file names may be
changed or edited as necessary to meet the requirements of the
SNMP Manager. Refer to the SNMP Manager documentation for
more information on these requirements.

Note:

In addition to the Spectracom MIB files, there are also

some net-snmp MIB files provided. Net-snmp is the embedded
SNMP agent that is used in the VelaSync and it provides traps to
notify the user when it starts, restarts, or shuts down. These MIB
files may also be compiled into your SNMP manager, if they are
not already present.

Spectracom’s private enterprise MIB files can be requested and obtained from
the Spectracom Customer Service department via email at

[email protected]

.

Note:

By default,

[email protected]

is the address

in the sysContact field of the SNMP Status panel of the SNMP
Setup page.

2.9.7.1

SNMP V1/V2c

SNMP V1 is the first version of the SNMP protocol, as defined in the IETF (Internet
Engineering Task Force) RFCs (Request for Comments) number 1155 and 1157. SNMP
V2c is the revised protocol, but it also uses the V1 community based administration
model.

Creating Communities

1.

Navigate to

MANAGEMENT > NETWORK: SNMP Setup

.

2.

In the

SNMP V1/V2

panel click the PLUS icon in the top-right corner.

3.

The

SNMP V1/V2c Settings for Access

window will display:

2.9 Configuring Network Settings

CHAPTER

2

•

VelaSync User's Manual Rev. 3

61

«
...
71
72
73
74
75
...
»

Содержание VelaSync 1225

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VelaSync 1225

Бренд: CAME Страницы: 32

Бренд: Zone Offroad Products Страницы: 5

Бренд: Eagly Eye Страницы: 3

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

CMT-U1BT - Micro Hi-fi Component System

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

CMT-NEZ3 - Micro Hi Fi Component System

Бренд: Sony Страницы: 32

CMT-U1BT - Micro Hi-fi Component System

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 43

CMT-DV2D - Micro Hi Fi Component System

Бренд: Sony Страницы: 54

Бренд: Sony Страницы: 61

Бренд: Sony Страницы: 94

CMT-DH7BT - Micro Hi Fi Component System

Бренд: Sony Страницы: 92

HCD-GX450 - Stereo Mini System

Бренд: Sony Страницы: 144

Бренд: DBL Technology Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды