Spectracom VelaSync 1225 Скачать руководство пользователя страница 60

Страница: 60 / 272

2.9.3

Network Services

Several standard network services can be enabled or disabled via the easily accessible

Network Services

Panel under

MANAGEMENT

Network Setup

The

Network Services

panel has ON/OFF toggle switches for the following daemons

and features:

SSH

: Secure Shell cryptographic network protocol for secure data com-

munication

HTTP

: Hypertext Transfer Protocol

tcpdump

: A LINUX program that can be used to monitor network traffic by

inspecting tcp packets. Default = ON.
If not needed, or wanted (out of concern for potential security risks),

tcpdump

can be disabled permanently: Once toggled to OFF, and after executing a page
reload,

tcpdump

will be deleted from the system: The toggle switch will be

removed, and the function cannot be enabled again (even after a software
upgrade).

2.9.4

Access Rules

Network access rules restrict access to only those assigned networks or nodes
defined. If no access rules are defined, access will be granted to all networks and nodes.

Note:

In order to configure Access Rules, you need

ADMINISTRATOR rights.

configure

a new, or

delete

an existing access rule:

CHAPTER

•

VelaSync User's Manual Rev. 3

2.9 Configuring Network Settings

Содержание VelaSync 1225

















































































































































































































































































Результаты поиска

Содержание VelaSync 1225

Отзывы:

Бренды по названию

Популярные бренды

Spectracom VelaSync 1225, Руководство пользователя

Результаты поиска

Содержание VelaSync 1225

Отзывы:

Бренды по названию

Популярные бренды