14
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
Warning:
Never use straight fuel in your unit.
This will cause permanent engine damage and void
the manufacturer’s warranty for that product. Never
use a fuel mixture that has been stored for over 90
days.
Warning:
If 2-cycle lubricant is to be used, it
must be a premium grade oil for 2-cycle air cooled
engines mixed at a 50:1 ratio. Do not use any 2-cycle
oil product with a recommended mixing ratio of
100:1. If insufficient lubrication is the cause of engine
damage, it voids the manufacturer’s engine warranty
for that occurrence.
Recommended fuels
Some conventional fuels are being blended with
oxygenates such as alcohol or an ether compound to
meet clean air standards. Your engine is designed to
operate satisfactorily on any fuel intended for
automotive use including oxygenated fuel. It is
recommended to use unleaded petrol as fuel.
Lubrication of chain and chain bar
Whenever you refill the fuel tank with petrol you must
also top up the level of chain oil in the chain oil tank. It
is recommended to use standard chain oil.
Engine pre-start checks
Warning:
Never start or operate the saw unless
the bar and chain are properly installed.
1.
Fill the fuel tank (A) with correct fuel mixture
(Fig. 8).
2.
Fill the oil tank (B) with chain oil (Fig. 8).
3.
Be certain the chain brake is disengaged (C)
before starting unit (Fig. 8).
Once you have filled the chain and oil tank,
tighten the tank cover securely by hand. Do not
use any tools to do so.
7. Operation
7.1 Starting the engine
1.
Set the On/Off switch (A) to “On (I)” to start the
machine (Fig. 9A).
2.
Pull out the throttle lever (B) (Fig. 9B) until it
locks.
3.
Push the primer bulb (C) 10 times (Fig. 9C).
4.
Place saw on a firm, flat surface. Hold saw firmly
as shown. Pull starter rapidly 2 times. Beware of
moving chain! (Fig.9D)
5.
Push in the throttle lever (B) as far as it will go
(Fig. 9B).
6.
Hold saw firmly and pull starter rapidly 4 times.
Engine should start (Fig. 9D).
7.
Let the engine run for 10 seconds to warm up.
Press the throttle lever (D) briefly, the engine will
go to “idling” speed (Fig. 9E).
If engine failed to start, repeat these instructions.
Important:
Always pull the starter cable slowly
until you feel the initial resistance before you then pull
it quickly to start the engine. Do not allow the starter
cable to whip back of its own accord.
7.2 Restarting a warm engine
1.
Make sure the switch is in the ON position.
2.
Pull the starter rope rapidly 6 times. The engine
should start.
7.3 To stop engine
1.
Release trigger and allow engine to return to idle
speed.
2.
Move STOP switch down to stop engine.
Note:
To stop the engine in an emergency, activate
the chain brake and switch the ON/OFF switch to
“Stop (0)”.
7.4 General cutting instructions
IMPORTANT:
Felling trees is prohibited without
the necessary training!
Felling
Felling is the term for cutting down a tree. Small trees
up to 6-7 inches (15-18cm) in diameter are usually cut
in a single cut. Larger trees require notch cuts. Notch
cuts determine the direction the tree will fall.
Warning:
A retreat path (A) should be planned
and cleared as necessary before cuts are started.
The retreat path should extend back and diagonally to
the rear of the expected line of fall, as illustrated in
Fig. 11.
Warning:
If felling a tree on sloping ground, the
chain saw operator should keep on the uphill side of
the terrain, as the tree is likely to roll or slide downhill
after it is felled.
Fuel and Oil Mix 50:1
Oil Only
