background image

 

Spartan Power SP-TS4500PLUS 

User Manual 

 

I. Application: 

This power transfer controller allows for trouble-free operation of an inverter and AC 
mains  on the same circuit. The SP-TS4500PLUS  switches automatically between 
inverter power and AC mains while protecting the inverter against external voltage. In 
addition, it offers the possibility to choose the battery power prior between the two 
power sources.   

 

II. Safety Instructions: 

The following safety notes and hazard warnings serve not only for the protection of 
the SP-TS4500PLUS but also for the protection of your health. 
In case of property damage or personal injuries caused by improper handling or 
non-observance of these operating instructions or the safety notes stated herein, the 
warranty will expire. We assume no liability for any consequential damages. 
1.

 

For safety and technical approval reasons, the unauthorized conversion and/or 

modification of the product is not permitted.   
2.

 

This power transfer controller is not a toy and must not be used by children! Please 

ensure childproof operation and storage of the power transfer controller at any time. 
Don’t leave packaging material heedlessly. It could become a hazardous toy for 
children! 
3.

 

Check the power transfer controller and connection cables before starting operation. 

If you detect any damages (e.g. transport damages) on the power transfer controller, 
do not start operation. Damaged connection cables must be replaced immediately. 
4.

 

The power transfer controller may only be operated in a dry environment to avoid 

getting humid or wet, otherwise there is a risk of life-threatening electrical shocks. 
5. The use of the product under unfavorable environmental conditions must be 
avoided under all circumstances. 
Unfavorable environmental conditions include: ambient temperatures above 50

flammable gases, solvents, vapors, dust, relative humidity in excess of 80%, and 
moisture. 
6. Do not use the switching station near ignition sources, open fire or other heat 
sources (heating, gas stoves or strong solar radiation).   
7. Service and repairs may only be carried out by authorized and qualified personnel. 
Use only original spare parts for repair work. The use of any other spare parts may 
lead to serious damage to property and personal injury! 
 

III. Product Introduction: 

This dual power transfer controller is used between an off-grid system and public 
power. The controller is separately connected with public power, inverter, battery and 
load.  On the top of the controller, there is an on/off switch, please turn on the 
controller after ensuring all cables are well connected.   

Содержание SP-TS4500PLUS








Отзывы: