Space-Ray PCA-SS 100 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 62

Space-Ray PCA-SS 100 Скачать руководство пользователя страница 15

Form 43343110

-14-

May 2021

8.0)

TYPICAL SUSPENSION METHODS

Various means of suspending the heater can be used. See the following drawings for typical examples.
1.

Use only noncombustible materials for suspending hangers and brackets.

2.

A minimum No. 2 chain with a working load limit of 115 lbs. is required.

3.

Turnbuckles can be used with chains to allow leveli

ng of the heater. All “S”

hooks and eye bolts must be

manually crimped closed by the installer.

4.

When using rigid means for heater suspension (rod, flat bar, etc.) provide sufficient lengths or swing joints to
compensate for expansion. See Figures b and c.

5.

Heaters subject to vibration must be provided with vibration isolating hangers.

6.

Heaters must not be supported by gas or electric supply lines and must be suspended from a permanent
structure with adequate load capacity.

Space-Ray recommends that the body sections be suspended using chains with turnbuckles. This will allow slight
adjustments after assembly and heater expansion/ contraction during operation.

«
...
13
14
15
16
17
...
»

Содержание PCA-SS 100































































Отзывы:

Нет отзывов