manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 45

Chapter

 

8 

 

Revision 004, 12/09 

 

35

 

General Maintenance 

 
 
 
 
 

Proper routine maintenance is the key to an efficiently operating unit with minimal 
downtime. The following section provides instructions on how to maintain your 
BenchTop series freeze dryer.  

Vacuum System 

Vacuum Pump 

Clean oil is necessary for the best vacuum and overall efficiency of the system. 
Checking and changing the oil on a consistent basis will greatly extend the life of the 
vacuum pump.  
 
Check the vacuum pump oil after each freeze-dry cycle by draining a small amount 
(~100 mL) from the pump drain line. Use a clear container to capture the sample. Oil 
should be changed as needed.  
 
When visually checking the oil, use the following guidelines: 

•

 

Pale yellow or clear vacuum pump oil indicates good condition. 

•

 

Dark vacuum pump oil indicates acid contamination. 

•

 

Cloudy gray vacuum pump oil indicates water contamination. 

Changing Vacuum Pump Oil 

Change the oil immediately after shutting down the freeze dryer while the oil is still 
hot. 

1.

 

Protect your hands from the hot oil. 

2.

 

Make sure vacuum is released from the system. 

3.

 

Remove the top fill plug and open the drain valve located at the bottom of the 
pump. Drain the contaminated oil into a suitable container. 

4.

 

When the oil has completely drained, close the valve and add new oil to the 
pump while visually checking the sight glass to ensure proper level (near the 
MAX line). Reinstall the fill plug. 

5.

 

If the pump oil is contaminated, operate the vacuum pump for 10 to 15 
minutes to flush any residual oil from the system’s interior components. 
Repeat steps 3 and 4 to complete the process. 

 

PROPERTY CAUTION!

 OIL MUST BE CHECKED AND CHANGED MORE FREQUENTLY IF YOUR 

PRODUCT CONTAINS CORROSIVE MATERIALS OR ORGANIC SOLVENTS. IN ADDITION, A 
FILTER TRAP MAY BE INSTALLED TO PROTECT THE VACUUM PUMP. 

© SP Industries, Inc. 2009 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды