manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 39

Chapter

 

7 

 

Revision 004, 12/09 

 

29

 

Optional Components 

 
 
 
 
 
The VirTis BenchTop series offers a wide variety of optional components to match a 
variety of product or process applications. 

Manifolds 

Many manifolds are available for BenchTop units. Optional manifolds include VirTis 
¾-inch (19 mm) Quickseal valves for attaching a variety of flasks, ampoules or vials. 
Stainless steel vertical manifolds are available for flask drying, while stainless steel 
and acrylic drum manifolds are available for the versatility of both flask and shelf rack 
drying. The top plug on acrylic drum manifolds is removable to allow for installation of 
an optional stoppering assembly.  
 
Available manifolds include: 

•

 

Stainless steel vertical manifolds with 4, 8, 12 or 24 ports. 

•

 

Stainless steel drum manifolds with 12 or 18 ports. 

•

 

Acrylic drum manifolds with 0, 8 or 12 ports. 

 

 

 

 

 

 

 

 

For more information about manifolds and current availability, contact SP Industries. 

 

© SP Industries, Inc. 2009 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды