manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 28

Sentry 2.0 Controls 

VirTis BenchTop 2K, 4K and 6K 

 
 

18 

 

Revision 004, 12/09 

Interstage Control 

If your unit is equipped with a cascade refrigeration system, you can control the 
operation of the second compressor from the Interstage Control screen. A cascade 
system is a safety feature used to protect the refrigeration system from overloading. 
 

∧

    Interstage Control 

 

Interstage                ON 

  ON –12            DIFF 025 

  Current Temp        1.3 

°

C 

 

If the Interstage Control is set to ON, the 

COND

 or 

AUTO

 buttons will activate the 

high-stage compressor. The Interstage Control’s Current Temp is monitored until the 
Interstage ON temperature is reached. Once the Interstage ON temperature is 
reached, the low-stage compressor is activated.  
 
The DIFF temperature is used to prevent overloading of the high-stage compressor. If 
the Current Temp exceeds the sum of the Interstage ON temperature and the DIFF 
value, the low-stage compressor is deactivated. It will reactivate when the Current 
Temp recovers. 

Calibration 

The Calibration screen allows modification and control of condenser temperature and 
vacuum settings. The following procedures require removal of the electrical box cover 
under the unit’s right-side panel. 
 

 

 

CAUTION! 

REMOVAL OF THE ELECTRICAL BOX EXPOSES HIGH-VOLTAGE COMPONENTS.  

USE EXTREME CAUTION AND FOLLOW ELECTRICAL SAFETY PRACTICES.

 

∧

    Calibration 

 

Temperature Span          070 

Temperature Zero  14.5C   128 

Vacuum      760 Torr      128 

Condenser Temperature Calibration 

To calibrate the condenser temperature, connect a thermocouple temperature 
simulator to the condenser temperature input. Set the simulator temperature to 25 °C.  
 
The current temperature is displayed on the Calibration screen. Adjust the numerical 
value of the Temperature Zero as appropriate and press 

MENU

 to enter the value. 

 
Upon proper adjustment of the Temperature Zero, change the temperature simulator 
value to -60 °C. Adjust the Temperature Span value so that the temperature displayed 
equals the calibrator set value. Recheck the value at 25 °C and repeat adjustment if 
necessary. Check calibration at desired temperature intervals for verification. 

 

 

© SP Industries, Inc. 2009 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды