manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 27

VirTis BenchTop 2K, 4K and 6K 

Sentry 2.0 Controls 

 

Revision 004, 12/09 

 

17

 

Maintenance Menu and Factory Options 

The Maintenance menus are used for system configuration, calibration and factory 
setup. Use caution when modifying factory settings.  
 

 

 

 

 
PROPERTY CAUTION! 

ENABLING FEATURES THAT ARE NOT INSTALLED MAY CAUSE SERIOUS 

SYSTEM DAMAGE AND VOID YOUR WARRANTY. ONLY A QUALIFIED SP INDUSTRIES TECHNICIAN 
SHOULD EDIT VALUES IN THE FACTORY OPTIONS AND INTERSTAGE CONTROL SCREENS. 
 

 

To access the Maintenance menu, press and hold the 

Up/Down (+/-) 

buttons 

simultaneously while on the Main Menu.  
 
 

∧

    Maintenance 

 

Factory Options        

>

 

Interstage Control     

>

 

Calibration            

>

 

 

Factory Options 

The Factory Options screen is used to configure the bath, purge, defrost and heat 
options.  
 

∧

    Factory options 

 

Bath Option         YES 

Purge Option        YES 

Hot Gas Defrost     YES 

Heat Option         No  

ZL Defrost          No 

 

 
The optional Heat and Purge components are enabled when set to YES. This results 
in changes to the Main Menu and Synoptic screens, adding control of these features.  

Note: 

The Heat and Purge options  require additional factory-installed components to function. 

If either option is purchased, the function will be enabled at the factory. If you are unsure 
whether you purchased the Heat or Purge option, contact SP Industries. 

The Hot Gas Defrost option uses a hot gas refrigeration loop to reduce defrost time. 
Setting the Hot Gas Defrost field to YES enables the hot gas defrost.

 

© SP Industries, Inc. 2009 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды