manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 25

VirTis BenchTop 2K, 4K and 6K 

Sentry 2.0 Controls 

 

Revision 004, 12/09 

 

15

 

© SP Industries, Inc. 2009 

Temperature Units 

The Temperature Units field displays the current setting for indicating temperature 
values. Temperature can be displayed in either Fahrenheit (°F) or Celsius (°C).  

Vacuum Units 

The Vacuum Units field displays the current setting for indication of system pressure. 
System pressure can be displayed in millitorr (mTorr), microbar (

μ

bar) or Pascal (Pa). 

Relay Test 

The Relay Test screen can be used to troubleshoot electrical or mechanical problems, 
or to observe active outputs during a freeze-drying run. 

 

∧

 Solid State Relay Output Test 

SSR1 SSR2 

-Vacuum -Purge 

-Comp2 -Bath 

-Comp1 -Spare 

-Defrost -Heat 

 

 

∧

-SSR1 

∨

-SSR2 Menu-Exit 

 
To test a relay bank, simply press the 

Up or Down (+/-) 

button and each of the 

outputs of the selected relay bank will fire for approximately two seconds each.  
Relay positions preceded by a highlighted box indicate the output is active.  

Vacuum Pump Maintenance  

The Vacuum Pump Maintenance screen is used to adjust vacuum maintenance alarm 
parameters and maintenance time durations. 

 

∧

  Vacuum Pump Maintenance 

 

Alarm Setpoint: 240 

Current Hours: 0000 min: 007 

 
The Alarm Setpoint is the number of hours of continuous operation the vacuum pump 
can run before the vacuum pump maintenance alarm will be generated. This can be 
used to draw attention to necessary vacuum pump maintenance operations, such as 
oil changes. The default factory value is 240 hours, but can be changed by pressing 
and holding the 

MENU

 button while Alarm Setpoint is highlighted. Once prompted, 

use the 

Up/Down (+/-) 

buttons to change this value. 

 
The Current Hours field can be reset at any time by pressing and holding the 

MENU

 

button while Current Hours is highlighted.  

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды