background image

12

Southworth Products

SR-44 Manual

4.2    Electrical Connections

The owner/installer is responsible for providing a fused disconnect 

switch. See section 8.1 Fusing Requirements.
Single phase machines must be connected to a dedicated circuit. 

Operating other equipment on the same circuit can cause excessive 

voltage drops and damage electrical components.

Make all connections according the wiring schematic. 

See section 8.2 Wiring Schematics.

4.3    Control Station

The control is shipped pre-wired to the machine. The control station must be placed in a location 

that allows the operator to see the load during operation but does not interfere with loading, 

unloading, and operation.

Mount the control station to the floor using the four mounting holes in the base plate. Anchors to 

be provided by installer.

4.4    Testing

Ensure all tools, personnel, and debris are clear of the area. 
During operation the movements should be smooth. Some bouncing/

stuttering may occur during initial operation caused by air in the 

hydraulic system. The air will bleed out of the system after several 

cycles. 
If the machine does not begin to rotate/clamp within several seconds of 

pressing the button, immediately release the button and consult section 

7. Troubleshooting.
Verify the maintenance chains are disengaged before operating the 

machine.

1.  Disengage the maintenance chains.
2.  Turn on the main disconnect switch to power the machine.
3.  Verify all personnel and debris are clear of the machine.
4. 

Press and hold the “Rotate CW” button. While the machine is rotating, press the emergency 

stop button. The machine should stop rotating and no longer function.

5.  Verify the machine is completely disabled by pressing each control button, the machine 

must not operate while the emergency stop is activated.

6. 

Reset the emergency stop button. Press and hold the “Rotate CW” button until the rotator 

mechanism reaches the end of travel.

7. 

Press and hold the “Rotate CCW” button until the rotator mechanism reaches the end of 

travel. Immediately release the button once the end of travel is reached. Allow the machine 

to rest for one minute. The machine should holds it position.

8. 

Press and hold the “Clamp” button until the clamp mechanism is fully clamped. Immediately 

release the button once the mechanism is fully clamped. Allow the machine to rest for one 

minute. The machine should hold its position.

9. 

Press and hold the “Unclamp” button until mechanism is fully opened. Immediately release 

the button once the mechanism is fully opened.

Содержание SR-44 Series

























Отзывы: