Contents Made in China
Product distributed by Southwire Company, LLC
One Southwire Drive, Carrollton, GA 30119
©2014 Southwire Company, LLC. All rights reserved.
southwiretools.com
1-855-SW-T00LS
Toll Free Technical Help
Línea de Ayuda Técnica Gratuita
Instrucciones de Operación
Detector de Voltaje AC Sin Contacto 40110N
Operating Instructions
40110N Non-Contact AC Voltage Detector
Introduction
The Southwire 40110N detects AC voltage from 100V to
1000V. A LED flashlight is built-in for added convenience.
With proper use, it will provide many years of reliable service.
International Safety Symbols
Potential danger. Indicates the user must refer to the
manual for important safety information
Indicates hazardous voltages may be present
Equipment is protected by double or reinforced insulation
• If the tester is used in a manner not specified by the manufacturer,
the safety features provided by the tester may be affected.
• Check on a known live source within the rated AC voltage range
of the tester before use to ensure it is in working order.
• Insulation type and thickness, distance from the voltage source,
shielded wires, and other factors may effect reliable operation.
Use other methods to verify live voltage, if there is any
uncertainty.
• Do not use if the tester appears damaged or if it is not operating
properly. If in doubt, replace the tester.
• Do not use on voltages that are higher than as marked on the
tester.
• Use caution with voltages above 30 volts AC as a shock hazard
may exist.
• Comply with local and national safety requirements - particularly
with regard to arc-flash potential.
• Use approved personal protective equipment when working on
live circuits.
WARNINGS
General Specifications
Detection voltage range
Frequency range
Batteries
Operating temperature
Storage temperature
Humidity
Altitude
Pollution Degree
Safety Compliance
100V AC to 1000V AC
50/60Hz
Two AAA 1.5V batteries
32°F to 122°F (0°C to 50°C)
14°F to 140°F (–10°C to 60°C)
80% max.
7000ft (2000m)
2
CAT IV-1000V
Maintenance
1. KEEP THE TESTER DRY. If it gets wet, wipe it off.
2. USE AND STORE THE TESTER IN NORMAL TEMPERATURES. Temperature extremes
can shorten the life of the electronic parts and distort or melt plastic parts.
3. HANDLE THE TESTER GENTLY AND CAREFULLY. Dropping it can damage the
electronic parts or the case.
4. KEEP THE TESTER CLEAN. Wipe the case occasionally with a damp cloth.
DO NOT use chemicals, cleaning solvents, or detergents.
5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE.
Remove old or weak batteries so they do not leak and damage the unit.
Brief Description
Typical Applications
Category
Rating
Three phase circuits
and single phase lighting
circuits in commercial
buildings
- Equipment in fixed installations such as 3-phase
motors, switchgear and distribution panels
- Lighting circuits in commercial buildings
- Feeder lines in industrial plants
- Any device or branch circuit that is close to
a CAT III source
- Primary distribution panels
- Overhead or underground lines to detached
buildings
- Incoming service entrance from utility
- Outdoor pumps
CAT III
CAT IV
Safety Category Ratings
Connection point to
utility power and outdoor
conductors
Detector Description
1. Flashlight
2. Flashlight power button
3. Battery cover & compartment
4. Detector tip
Operation
Checking for live AC voltage (100V to 1000V)
1. Prior to use, test on a known live circuit to verify tester is functioning.
Place the tip of the sensor near an AC voltage source. If the tester detects
voltage within the defined detection range, the red light will turn on with
a steady glow and the beeper will produce a continuous tone.
4. Carefully slide the battery cover onto the tester making sure the cover
is aligned with the slots on the tester body. Make sure the battery cover
is completely closed.
3. Replace the batteries (observe polarity). Use two AAA 1.5V batteries.
TESTING EQUIPMENT
E361819
Battery Replacement
Steps 1. and 2.
5. Verify operation by using the tester on a known live AC voltage.
®
2.
Flashlight -
Press and hold the button with the symbol to turn on the
flashlight. Release the button to turn off the flashlight.
NOTES:
• The tester is always active and ready to use, providing the batteries
are installed and in good condition.
• The detector is designed for high sensitivity. Static electricity may momentarily
activate the sensor. This is normal operation.
Scan for warranty information
and to access our mobile site.
Escanea para información de garantía
y acceso a nuestro sitio móvil.
®
4.
1.
2.
3.
4.
3.
REGISTER YOUR PRODUCT
Register your product purchase at
www.southwiretools.com
or by
scanning the QR code on this manual. At Southwire, we are dedicated to
providing you with the best customer experience. By following a few quick
steps to register, you can experience quicker service, more efficient support,
and receive information on our future products. Simply provide your model
number, serial number, and just a few pieces of information about yourself –
it is that quick and easy.
LIMITED WARRANTY AND LIMITATION OF LIABILITY ON
SOUTHWIRE METERS & TESTERS
Southwire Company, LLC warrants this product to be free from defects in
material and workmanship for two years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage arising from
an accident, neglect, misapplication, contamination, modification, improper
maintenance or repair, operation outside of specifications, or abnormal
handling of the product. Southwire’s sole liability, and the purchaser’s
exclusive remedy, for any breach of this warranty is expressly limited to
Southwire’s repair or replacement of the product. Whether Southwire repairs
or replaces the product will be a determination that Southwire makes at its
sole discretion.
SOUTHWIRE MAKES NO WARRANTY THAT THE PRODUCT WILL
BE MERCHANTABLE OR FIT FOR ANY PARTICULAR PURPOSE.
SOUTHWIRE MAKES NO OTHER WARRANTY, EXPRESSED OR
IMPLIED, OTHER THAN THE WARRANTY SPECIFICALLY SET FORTH
HEREIN. SOUTHWIRE WILL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES FOR
ANY BREACH OF THIS WARRANTY.
This warranty is void if this product is used for rental purposes. No product
reseller is authorized to extend any other warranty on Southwire’s behalf
relating to this product, and no such reseller warranty will be binding on
Southwire. If you have a warranty claim, or if the product needs to be
serviced during or after the warranty period set forth above, please contact
the Customer Service Department at 855-SWTOOLS (855-798-6657).
The sender is responsible for all shipping, freight, insurance, and packaging
costs associated with sending a product to Southwire. Southwire will not be
responsible for lost or damaged products returned pursuant to this warranty.
All products returned to Southwire under this warranty should be mailed to:
Southwire Company, LLC
Attention: Tool Warranty Return
840 Old Bremen Road
Carrollton, GA 30117
1.
Press HERE
(A.)
2.
Pull down here
(B.)
, applying a gentle
bending force until you hear a click,
then pull off the battery cover
NOTE:
• When batteries are loaded for the first time, please remove the white,
rectangular security strip before installing batteries.
Pull off battery cover
A.
B.
