South bend SB1493 Скачать руководство пользователя страница 4

Страница: 4 / 32

INTRODUCTION

-2-

For Machines Mfd Since 1/21

South Bend Tools

Model SB1493

I N T R O D U C T I O N

Controls & Components

Serious personal injury could occur if

you connect the machine to power before

completing the setup process. DO NOT

connect power until instructed to do so later

in this manual.

Untrained users have an increased risk

of seriously injuring themselves with this

machine. Do not operate this machine until

you have understood this entire manual and

received proper training.

Spindle:

Secures and spins buffing wheels

Accepts

" bore wheels of up to 12" diameter

Wheel Flanges:

Hold buffing wheel

Bushings:

Support flange to hold buffing wheel

securely

Digital Tachometer:

Displays spindle RPM

Variable-Speed Dial:

Rotates to adjust buffing

speed Variable-speed dial must be turned fully

counterclockwise for motor to start

ON/OFF Switch w/Disabling Key:

Turns motor

ON when moved up; turns motor OFF when

moved down When key is removed, switch is

disabled and machine cannot start

Spindle

ON/OFF Switch

w/Disabling Key

Variable-Speed

Dial

Digital Tachometer

Wheel Flanges

Bushings

Содержание SB1493

































Результаты поиска

Содержание SB1493

Отзывы:

Похожие инструкции для SB1493

Бренды по названию

Популярные бренды

South bend SB1493, Руководство пользователя

Результаты поиска

Содержание SB1493

Отзывы:

Похожие инструкции для SB1493

Бренды по названию

Популярные бренды