South bend SB1108 Скачать руководство пользователя страница 39

Страница: 39 / 76

South Bend Tools

For Machines Mfd. Since 12/20

Model SB1108/SB1109

-37-

M A I N T E N A N C E

Note:

SAE 140 Gear Oil or SAE 85W-140 multi-

weight gear oil may also be used. DO NOT mix

oil types!

Note:

We recommend that you replace the

gearbox oil after the first 20 hours of operation.

This is a normal break-in procedure and will

help maximize the service life of the machine by

flushing away any particles from the break-in

process.

Although it is not necessary to remove the drive

chain cover to access the fill and drain plugs, it

is more convenient to do so (see Figures 44–45).

Drain the old oil into a pan. Re-install the drain

plug, then refill the gearbox with ISO 320 or

equivalent oil until it just reaches the fill plug.

Re-install the fill plug.

Figure 44. Location of gearbox oil drain plug.

Drain Plug

Gearbox

Cover

Figure 45. Location of gearbox oil fill plug.

Fill Plug

Gearbox Oil

Oil Type ................ T28042 or ISO 320 Equivalent

Oil Amount ................................................... 20 Oz.

Frequency ....... After First 20 Hours, Then Yearly

Anti Kickback Fingers

Check the anti-kickback fi ngers regularly to

ensure they swing freely and easily. If the fi ngers

do not swing freely and easily, fi rst clean them

with a wood-resin solvent, then inspect them

for damage. If any of the fi ngers are damaged,

the device must be replaced before using the

machine.

Do not apply oil or other lubricants to the anti-

kickback fi ngers that will attract dust and

restrict free movement of the fi ngers.

Proper operation of anti-kickback fingers is

critical for safe operation of this planer. DO

NOT operate planer if anti-kickback fingers are

not operating correctly. Failure to heed this

warning could result in serious personal injury.

The anti-kickback fingers are an important

safety feature of your planer. The fingers hang

from a rod suspended across the head casting

and in front of the infeed roller, as shown. This

design allows the workpiece to easily enter

the planer but reduces the risk of kickback by

digging into the workpiece if it moves backward.

Anti-Kickback Fingers

Figure 46. Example of anti-kickback fingers.

Anti-Kickback Fingers

Содержание SB1108













































































Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды

South bend SB1108, Руководство пользователя

Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды