background image

©   Soundcraft Electronics Ltd.  1991 
All rights reserved

Issue 1 
Part No. ZZ2727

Information in this manual is subject to change without notice and does not represent a
commitment on the part of the vendor. Soundcraft Electronics Ltd. shall not be liable for
any loss or damage whatsoever arising from the use of information or any error contained
in this manual.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, electrical, mechanical, optical, chemical, including
photocopying and recording, for any purpose without the express written permission of
Soundcraft Electronics Ltd.

It  is recommended that all maintenance and service on the product should be carried out
by Soundcraft Electronics Ltd. or its authorised agents. Soundcraft Electronics Ltd. cannot
accept any liability whatsoever for any loss or damage caused by service, maintenance or
repair by unauthorised personnel.

Soundcraft Electronics Ltd. 
Unit 2
Borehamwood Ind Park
Rowley Lane
Borehamwood 
Herts. 
WD6 5PZ 
England  

Tel:   081 207 5050
Fax: 081 207 0194

Page 2

Содержание Spirit Monitor





























Отзывы: