Sound Performance Lab MMC2 Скачать руководство пользователя

Страница: 19 / 20

Dynamic Range

›130 dB

Max. input level

›30 dBu

(Audio Precision generator limit +30 dBu)

THD & Noise

(+24 dBu)

Recording Out:

›110 dBu

Monitor Out:

›108 dBu

Send: ›110

dBu

Input impedance (balanced):

20 kOhm

(Welwyn precision resistors, transformerless)

Output impedance (balanced):

‹75 Ohm

(CMR trimmers, transformerless)

Dimensions

Front panel

19 inch/11U

Housing incl. connectors (H x W x D)

51.6 x 48.2 x 52 cm/20,3 x 19 x 20.5 inch

Weight

35 kg/77 lb

Power Supply

For optimal audio quality and dramatically reduced inductive disturbance/
interference, the MMC 2’s power supply is divided into two parts. The external
part houses a toroidal transformer, the linear power supply is built into the MMC 2
housing.

Input voltage:

110-120 V/60 Hz or 220-240 V/50 Hz

Fuses external transformer:

5 AT (slow)

Fuses internal power supply:

+/- 62 Volt PWS 2AT (slow)

Power consumption:

A@230 V, 1,6 A@110-120 V

Noise:

› -100 dBu (@ +/- 60 V)

Dimensions ext. transformer:

Width: 15 cm (5 9/10 inch)

Depth: 24,5 cm (24 1/2 inch)

Height: 7 cm (2 3/4 inch)

Weight ext. transformer:

4,2 kg (9,24 lbs)

Speciﬁ cations/Power Supply

Содержание MMC2





















Результаты поиска

Содержание MMC2

Отзывы:

Похожие инструкции для MMC2

Бренды по названию

Популярные бренды

Sound Performance Lab MMC2, Руководство пользователя

Результаты поиска

Содержание MMC2

Отзывы:

Похожие инструкции для MMC2

Бренды по названию

Популярные бренды