Sony XPERIA Ion LT28at Скачать руководство пользователя страница 154

Страница: 154 / 224

Troubleshooting Guide (mech)

1261-4721 Rev 3



Sony Mobile Communications AB

– Company Internal

21(62)

Problem Areas

1.8 Microphone

1.8.1 Microphone

Check:

Inspect the Microphone

„s external port on the Cover Front

Assy.

Action:

1. If clogged

– clean the port.

2. If the port is damaged

– replace the Cover Front Assy.

Note: Ensure the BtB connector of battery is
disconnected in the following steps!

Check:

Inspect the gasket Mic (a),the microphone (b) and rubber
Mic (c)

Action:

If there has gasket Mic (a)

– remove it.

The gasket Mic(a) must be removed!

If there is no Rubber Mic (c) on microphone (b)

–

assemble a rubber Mic (c) as show in the picture.

Содержание XPERIA Ion LT28at

































































































































































































































Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды

Sony XPERIA Ion LT28at, Руководство по эксплуатации

Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды