Sony XDCAM PDW-HR1, Руководство по эксплуатации, Страница: 40 / 214

40
Connector Panel
Chap
te
r 2
Name
s
an
d
F
u
nc
tio
n
s
o
f P
a
rts
AUDIO CONFIG >M372: NON-AUDIO INPUT
(recording)
(see page 165) and setup menu item 823 NON-
AUDIO FLAG PB (playback).
l
REMOTE(9P) (remote control 9-pin) connector
(D-sub 9-pin)
To control this unit from a controller or VTR supporting
the RS-422A Sony 9-pin VTR protocol, connect the device
to this connector.
m
SDSDI OUTPUT (SDI signal output) connector
(BNC type)
Output SDSDI format video/audio signals.
When the unit is shipped from the factory, audio signal
output is eight channels with no switching, and RP188
timecode output is set to on. You can change these settings
with setup menu item 828 SDI AUDIO OUTPUT
SELECT and setup menu item 920 SD-SDI H-ANC
CONTROL.
See page 145 for more information about setup menu
operations.
n
DVB-ASI OUTPUT connector
When the PDBK-202 option board is installed, outputs
DVB-ASI TS signals.
o
MAINTENANCE connectors
These are the USB connectors for maintenance.
Connect a Windows USB keyboard or mouse
(see
page 86) , or a USB flash drive to access planning metadata
stored on the drive (see page 98) .
p
HDMI OUT connector
Outputs digital signals (video, audio, control signals). Use
a HDMI cable to connect a high- definition projector, a
high-definition television, or another consumer electronics
product.
Signals of the audio channels selected with the AUDIO
MONITOR SELECT buttons
(see page 26) are output.
q
(network) connector (RJ-45 type)
This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• When you connect the network cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
• Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une
tension excessive à ce port. Suivez les instructions pour
ce port.
• Lors de la connexion du câble réseau de l’appareil au
périphérique, utilisez un câble blindé afin d’empêcher
tout dysfonctionnement dû au bruit de rayonnement.
• Aus Sicherheitsgründen nicht mit einem
Peripheriegerät-Anschluss verbinden, der zu starke
Spannung für diese Buchse haben könnte. Folgen Sie
den Anweisungen für diese Buchse.
• Verwenden Sie beim Anschließen des Netzwerkkabels
des Geräts an ein Peripheriegerät ein abgeschirmtes
Kabel, um Fehlfunktionen aufgrund von Störungen zu
vermeiden.
r
COMPOSITE IN/OUT (analog composite video
input and output) connectors (BNC type)
Input and output analog composite video signals.
s
TIME CODE IN/OUT (timecode input and output)
connectors (BNC type)
Input SMPTE timecode generated by an external device to
the IN connector.
The timecode output from the OUT connector depends on
the operating status of this unit, as follows.
During playback: Playback timecode
During recording: The timecode from the internal
timecode generator or the timecode input to the TIME
CODE IN connector
t
REF.VIDEO OUT (reference video signal output)
connector (BNC type)
When this unit is running, outputs the reference video
signal that is input to the REF VIDEO IN connector.
u
REF.VIDEO IN (reference video signal input)
connector (BNC type)
Inputs the system frequency reference video signal
selected with setup menu item 013 SYSTEM
FREQUENCY SELECT MENU. This connector is
terminated with an impedance of 75 ohms.
CAUTION
ATTENTION
VORSICHT