Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 214

Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 186

186

Troubleshooting

A

ppen

dix

Alarms related to system frequency and recording format

The following alarms are displayed only when setup menu
item 016 ALARM DISPLAY is set to “on” or “limit”.

Error messages

Error codes appear in the time data display when an error
(usually a hardware problem) occurs. In addition, both
error messages and error codes appear in the video monitor
screen and on the video monitor connected to the unit.
When an error message appears, follow the instructions in
the error message to resolve the problem.

Unknown USB

UNKNOWN USB DEVICE.

The USB connector of this unit is for maintenance
purposes and connection of USB devices. Connect a
compatible USB device.

Alarm message in time
data display area

Alarm message in video monitor screen Action

Alarm message in time
data display area

Alarm message in video monitor screen Action

1080/59.94i

RECORDING AND PLAYBACK IS NOT
POSSIBLE.
SYSTEM FREQUENCY SELECTION
DIFFER FROM IT ON DISC.

This appears when the system frequency selection of
the unit differs from that of the loaded disc.Insert a
disc with the same system frequency as the unit, or
change the unit’s system frequency.

1080/29.97P

1080/50i

1080/25P

1080/23.98P

720/59.94P

720/50P

525/59.94i

625/50i

1080/59.94i

DISC CANNOT BE RECORDED.
VIDEO RESOLUTION DIFFER FROM IT
ON DISC.

This appears when the number of system lines set in
this unit does not correspond to the resolution for the
inserted disc.
Change the disc to the one corresponding to the
number of system lines set in this unit or change the
number of system lines of this unit.

1080/50i

1080/29.97P

1080/25P

1080/23.98P

720/59.94P

720/50P

HD422 1080

DISC CANNOT BE RECORDED.
VIDEO REC MODE SELECTION
DIFFERENT FROM VIDEO ON DISC.

This appears when the video recording format of this
unit does not correspond to that of the inserted disc.
Change the disc to the one corresponding to the
video recording format of this unit or change the video
recording format of this unit.

HD422 720

HD420 1080

HD420 720

IMX50 Clip

IMX40 Clip

IMX30 Clip

8CH×16 Clip

DISC CANNOT BE RECORDED.
AUDIO REC MODE SELECTION
DIFFERENT FROM AUDIO ON DISC.

This appears when the audio recording format of this
unit does not correspond to that of the inserted disc.
Change the disc to the one corresponding to the
audio recording format of this unit or change the
audio recording format of this unit.

4CH×24 Clip

2CH×16 Clip

«
...
184
185
186
187
188
...
»

Содержание XDCAM PDW-HR1























































































































































































































Отзывы:

Нет отзывов