manualshive.com logo in svg

Sony XDCAM PDW-HR1, Руководство по эксплуатации, Страница: 177 / 214

Поделиться
Скачать
Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 177

177

Troubleshooting

  

A

ppe

ndix

Troubleshooting

Alarms

An alarm (warning message) appears in the time data 
display area when an operation is attempted which is 
inappropriate for the settings on this unit or the state of the 
disc. Both the alarm message and the action to take to 
resolve the problem appear in the video monitor screen and 
on the screen of the external video monitor connected to 
the unit.

When an alarm is displayed, remove the alarm cause by 
following the action to take. If the alarm display does not 
disappear, contact a Sony service representative.
Please note that there are some alarms which do not appear 
depending on the setting of setup menu item 016 ALARM 
DISPLAY 

(see page 143)

.

See “Setup Menu” (page 140) for more information about 
setup menu operations.

When the unit is powered on

ALARM

       REMOTE MODE IS SELECTED.

       SET REMOTE/LOCAL/NETWORK
           SWITCH TO LOCAL.

Example alarm in time data display area

Example alarm in video monitor screen

Alarm message in time 
data display area

Alarm message in video monitor screen

Description/action

ADJ. Mode!

THE UNIT IS IN ADJUSTMENT MODE.
CHECK THE SWITCHES OF S2200 ON THE 
HPR-31 BOARD AND S500 ON THE NET-5 
BOARD.

This appears when the unit is in adjustment 
mode.
Contact a Sony service representative.

MENU Ver.UP

THE SETUP MENU SOFTWARE HAS BEEN 
UPGRADED.
SET THE SETUP MENU ITEMS TO THE 
DESIRED SETTINGS.

Reset the settings in the setup menu 

(see 

page 146)

.

ILL. SETUP!

INVALID SETTINGS SELECTED IN SETUP 
MENU.
SET ITEMS IN THE SETUP MENU TO THE 
APPROPRIATE VALUES. CONTACT SERVICE 
IF THIS ALARM APPEARS AGAIN AFTER 
ABOVE PROCEDURE.

Reset the settings in the setup menu 

(see 

page 146)

. If the same message appears after 

you reset the settings, contact a Sony service 
representative.

Exchg batt!

BATTERY NEEDS REPLACING. PLEASE 
CONTACT SERVICE.

The NVRAM battery is exhausted. Contact a 
Sony service representative.

Update Err!

RUN SOFTWARE UPDATE PROGRAM.

The software version is not properly updated.
Update the software version again. If the same 
message appears after you update the software 
version, contact a Sony service representative.

Содержание XDCAM PDW-HR1























































































































































































































Отзывы:

Нет отзывов