Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 150

Страница: 150 / 214

150

Setup Menu

ap
te

r 8

enu

a) The disc is ejected after recording stops.

b) The unit enters stop mode when the PLAY button is pressed. It enters

freeze picture mode (jog, shuttle, or variable mode) when the SHUTTLE/
JOG button or VAR/JOG button is pressed.

a) When the PDBK-202 option board is installed

b) FTP connections can be made only when the device connected to the

REMOTE(9P) connector (D-sub 9 pin) is in stop mode. During FTP
connections, the device connected to the REMOTE(9P) connector cannot
be used to control this unit.

153

FIND MODE

Specify the frame to be cued up when the PREV or NEXT button is
pressed.

clip:

The first frame of the clip

R.ST (clip & rec start mark):

The frame where a Rec Start essence

mark is set (if no essence mark is set, the first frame of the clip)

154

SINGLE CLIP PLAY MODE

Put the unit into single clip playback mode, or exit from single clip
playback mode.

off:

Exits from single clip playback mode. (Puts the unit into continuous

playback mode.)

on:

Puts the unit into single clip playback mode.

Menu items in the 100s, relating to the control panels (OPERATIONAL PARAMETER)

Item number Item name

Settings

Menu items in the 200s, relating to the remote control interface (REMOTE INTERFACE)

Item number

Item name

Settings

201

PARA RUN

Select whether to use synchronized operation for two or more VTRs.

dis (disable):

No synchronized operation

ena (enable):

Use synchronized operation

Note

To use synchronized operation for two or more VTRs, set item 201 to ena
on all of the VTRs.

214

REMOTE INTERFACE

When the remote control switch is set to REMOTE, select the device
from which to remote-control this unit.

9PIN:

Device connected to the REMOTE(9P) connector.

SDI:

Device connected to the SD/HDSDI INPUT connector.

i.LINK:

Device connected to the (i.LINK) HDV TS connector.

257

NETWORK ENABLE

Select the remote control switch positions which enable network
connections.

net (network):

Only when the switch is set to “NET”.

n&9P (network & remote(9PIN)):

When the switch is set to “NET”, and

when the switch is set to “REMOTE” and setup menu item 214 is set
to “9PIN”.

Menu items in the 300s, relating to editing operations (EDITING)

Item number Item name

Settings

301

VAR SPEED RANGE FOR
SYNCHRONIZATION

Select the playback speed range when carrying out playback in variable
speed mode from a remote control unit connected to the REMOTE(9P)
connector.
–

1~+1:

–1 to +1 times normal speed.

wide:

–1.20 to +1.20 times normal speed.

307

AUTO-DELETION FOR
INCONSISTENT DATA

Select what to do when an inconsistent edit point has been set.

manu (manual):

Flash the DELETE button on the control panel and

display a warning.

neg&E (neg & excess):

Delete the inconsistent edit point automatically

when an Out point is set before an In point, and when more edit
points than necessary have been set.

neg:

Delete the inconsistent edit point automatically when an Out point

is set before an In point. Flash the DELETE button on the control
panel and display a warning when more edit points than necessary
have been set.

Содержание XDCAM PDW-HR1























































































































































































































Результаты поиска

Содержание XDCAM PDW-HR1

Отзывы:

Sony XDCAM PDW-HR1, Руководство по эксплуатации, Страница: 150 / 214

Результаты поиска

Содержание XDCAM PDW-HR1

Отзывы: