44
Basic Operations of the Function Menu
Ch
apt
er 3 Prep
ar
at
ion
s
a) This is displayed only when TCG on page P5 TC of the function menu is
set to “INT”, and PRST/RGN is set to “PRESET”.
P1 VIDEO page
P2 AUDIO page
F4: CNTR SEL
Selects the type of time data to display in
the time data display area.
TC:
Timecode
COUNTER:
Elapsed recording or
playback time
UB:
User bits
F5: TCG SET
• When CNTR SEL is set to “TC”,
displays a screen where you can set
the initial value of the timecode
generated by the internal timecode
generator
a)
.
• When CNTR SEL is set to “UB”,
displays a screen where you can set
timecode user bits
a)
F6:
(Unassigned function button)
Item
Setting
F1: V INPUT
Selects the video input signal.
HDSDI:
HDSDI signal
SDSDI:
SDSDI signal
SG:
Test signal from internal signal
generator (Normally this item is not
displayed. It appears when you hold
the button down for 3 seconds.)
F2: VID. PROC
Selects the method used to control the
internal video signal processor and make
related settings.
LOCAL:
Use the function menu to
change settings.
MENU:
Use the setup menu to change
settings.
F3: VIDEO
Sets the output level for HD/SD video
signals (range –
∞
to +3 dB).
PRESET:
Set the video signal output
level to a preset value, regardless of
manual setting.
Manual setting:
While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the video
signal output level.
F4: CHROMA
Sets the output level for HD/SD chroma
signals (range –
∞
to +3 dB).
PRESET:
Set the chroma signal output
level to a preset value, regardless of
manual setting.
Manual setting:
While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the
chroma SETUP signal output level.
Item
Setting
F5: HUE/CHRM
PHS
Sets the hue (chroma phase).
PRESET:
Set the hue (chroma phase) to
a preset value, regardless of manual
setting.
Manual setting:
While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to adjust the hue
(chroma phase) over the range
±30°.
F6: SETUP/
BLACK
Sets the HD/SD output black setup level
or black level.
PRESET:
Set the level to the preset
value, regardless of the manual
setting.
Manual setting:
While the setting value
is flashing, turn the PUSH
SET(S.SEL) knob to set the black
setup level (in 59.94i/29.97P mode)
over the range ±30 IRE or the black
level (in 50i/25P mode) over the
range ±210 mV.
Item
Setting
F1: A1 INPUT
Selects the audio input signal to assign
to audio channel 1.
SDI:
Audio signal embedded into SDI
signal
ANALOG1:
Analog 1 audio signal
SG:
Test signal from internal signal
generator (Normally this item is not
displayed. It appears when you hold
the button down for 3 seconds. The
test signal is assigned to audio
channels 1 to 8 simultaneously.)
Press one of the function buttons
corresponding to A1 INPUT to A8
INPUT again to stop output of the
test signal.
F2: A2 INPUT
Selects the audio input signal to assign
to audio channel 2.
SDI:
Audio signal embedded into SDI
signal
ANALOG2:
Analog 2 audio signal
F3: MONITR L
Selects the channel to monitor as the left
monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F4: MONITR R
Selects the channel to monitor as the
right monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F5: SPEAKER
Enables or disables output from this
unit’s speaker.
OFF:
Do not output
ON:
Output
Item
Setting
Содержание XDCAM PDW-HD1200
Страница 1: ...PROFESSIONAL DISC RECORDER PDW HD1200 OPERATION MANUAL English 1st Edition Revised 1 ...
Страница 9: ...Table of Contents 9 Glossary 172 Index 174 ...
Страница 167: ...167 List of Supported USB Keyboards Appendix ...
Страница 178: ...Sony Corporation PDW HD1200 SYL 4 427 654 02 1 2012 ...