Sony XC-505P Скачать руководство пользователя страница 22

Страница: 22 / 34

Camera Control Commands

3D-NR Setting

Pedestal Setting

Gamma Table Setting

Polarity (Nega/Posi) Setting

High Brightness Clipping Setting

WPC (White Pixel Compensation)

Enable/Disable White Point Detection
Compensation

Execute Auto White Point Detection

White Point Compensation Marker Setting

Command
Name

3DNR-MODE

Parameter 1

Filter selection: 0 to 3

0: 3D-NR disabled
1: Mild 3D-NR
2: Moderate 3D-NR
3: Strong 3D-NR

Default is 0

Conditions

None

Process

Sets the strength of 3D-NR noise
suppression. Higher noise suppression
corresponds to lower dynamic resolution as
the afterimage becomes more visible.

Command
Name

PEDESTAL

Parameter 1

0 to 22 (corresponds to NTSC: 0 to 10 [IRE],
and PAL: PAL 0 to 70 [mV])
Default is 11 (NTSC: 5 [IRE], and PAL: 35
[mV])

Conditions

None

Process

Adjusts the pedestal.
Does not affect gamma-curve compensation.

Command
Name

GAMMA-MODE

Parameter 1

Gamma curve: 0 to 2

= 1.0

= 0.45(

= 1/2.2)

= 0.6(

= 1/1.6)

Default is 1

Conditions

None

Process

Specifies the gamma curve of the YC signal
(the specified C is used regardless of the
GAMMA-MODE setting.)

Command
Name

NEGAPOSI

Parameter 1

Polarity: 0 to 1

0: Positive
1: Negative

Default is 0

Conditions

None

Process

Inverts the YC signal after gamma curve
compensation.

Command
Name

WHITECLIP

Parameter 1

Brightness signal clipping level: 0 to 63

0: Minimum to
1: Maximum (no clipping)

Default is 63

Conditions

None

Process

Clips brightness exceeding the specified level
in the final output of the Y signal.
Use this function to avoid image whiteout.

Command
Name

WPC-MODE

Parameter 1

White point detection compensation enable/
disable: 0 to 1

0: OFF
1: ON

Default is 1

Conditions

None

Process

Enables or disables auto detection of white
point compensation.

Command
Name

WPC-EXE

Parameter

None

Conditions

None

Process

Starts auto white point detection processing.
Execute with the lens covered, such as by a
lens cap.

Command
Name

WPC-DISP

Parameter 1

Marker display/non-display: 0 to 1

0: OFF
1: ON

Default is 0

Conditions

Display is only possible when WPC-MODE is
1.

Process

The marker indicates the white point location
on the object of compensation.

Содержание XC-505P



































Результаты поиска

Содержание XC-505P

Отзывы:

Похожие инструкции для XC-505P

Бренды по названию

Популярные бренды

Sony XC-505P, Техническое руководство

Результаты поиска

Содержание XC-505P

Отзывы:

Похожие инструкции для XC-505P

Бренды по названию

Популярные бренды