background image

XAV-65

3

SECTION  1

SERVICING  NOTES

NOTES  ON  HANDLING  THE OPTICAL  PICK-UP  
BLOCK  OR  BASE  UNIT

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by 
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also 
use the procedure in the printed matter which is included in the 
repair parts.
The fl exible board is easily damaged and should be handled with 
care.

NOTES  ON  LASER  DIODE  EMISSION  CHECK

The laser beam on this model is concentrated so as to be focused 
on the disc refl ective surface by the objective lens in the optical 
pickup block. Therefore, when checking the laser diode emission, 
observe from more than 30 cm away from the objective lens.

Label indication

Destination

Signal format 

system

Region 

code

Part No.

NTSC

1

4-476-347-0

[]

US and Canadian 
models

NTSC

4

4-476-348-0

[]

E (NTSC) model

PAL

3

4-476-349-0

[]

E (PAL) model

PAL

5

4-476-350-0

[]

Indian model

PAL

2

4-476-351-0

[]

AEP and UK models

PAL

5

4-476-352-0

[]

Russian model

PAL

2

4-558-479-0

[]

Saudi Arabia model

PAL

4

4-558-480-0

[]

Australian model

MODEL  IDENTIFICATION

Part No.

– Bottom View –
(Except E (NTSC) Indian and Australian models)

Region Code
(E (PAL) model)

Region Code
(AEP, Russian and UK models)

Part No.

Region Code

– Bottom View –
(E (NTSC) Indian and Australian models)

Region Code
(Saudi Arabia model)

Region Code
(US and Canadian models)

ABOUT  THE  SECURITY  FUNCTION

This unit does not use security function by password lock.

NOTE  FOR  TRANSPORTATION 

When this unit is transported, it is necessary to install two transpor-
tation screws. Please transport it after installing two transportation 
screws as shown in the fi gure below.

Part No. 

Description

A-2018-257-A  SCREW WITH WARNING LABEL

WARNING!!!

Warning label

u

1

Transportation screw

u

2

WARNING!!!

warning label

transportation screw

transportation screw

Replacing the lithium battery of the 
remote commander

(E (NTSC) and Indian models only)

Under normal conditions, the battery will last 
approximately 1 year. (The service life may be 
shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the 
remote commander becomes shorter. Replace the 
battery with a new CR2025 lithium battery. Use of 
any other battery may present a risk of fire or 
explosion. 

+ side up

Notes on the lithium battery

Keep the lithium battery out of the reach of children. 
Should the battery be swallowed, immediately 
consult a doctor.
Wipe the battery with a dry cloth to assure a good 
contact.
Be sure to observe the correct polarity when installing 
the battery.
Do not hold the battery with metallic tweezers, 
otherwise a short-circuit may occur.
Do not expose the battery to excessive heat such as 
direct sunlight, fire or the like.

WARNING

Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of in 
fire.

Ver. 1.1

Содержание XAV-65























Отзывы: