Sony Vaio VGN-S350F, Руководство по обслуживанию

Страница: 8 / 173

1-3
IC
VGN- S36C/S36GP/S36LP/S36SP/S36TP/S38CP/ S52B/
S62PS/S62PSY/S62S/ S350F/S350FP/ S360/S360P/ S370F
(J/AM /AO )
Confidential
ADM1032ARM-REEL (ADI)
SYSTEM TEMPERATURE MONITOR
TOP VIEW
(Not to Scale)
8
7
6
5
1
2
3
4
D+
SCLK
D–
THERM
ADM1032
V
DD
GND
ALERT
SDATA
PIN FUNCTION DESCRIPTIONS
Pin
No.
Mnemonic Description
1 V
DD
Positive Supply, 3 V to 5.5 V.
2 D+ Positive Connection to Remote Temperature Sensor.
3 D– Negative Connection to Remote Temperature Sensor.
4
THERM THERM
is an open-drain output that can be used to turn a fan on/off or throttle a CPU clock in the event of
an overtemperature condition. Requires pull-up to V
DD
.
5 GND Supply Ground Connection.
6
ALERT
Open-Drain Logic Output Used as Interrupt or SMBus Alert.
7 SDATA Logic Input/Output, SMBus Serial Data. Open-drain output. Requires pull-up resistor.
8 SCLK Logic Input, SMBus Serial Clock. Requires pull-up resistor.
ADM1032–SPECIFICATIONS
(T
A
= T
MIN
to T
MAX
, V
DD
= V
MIN
to V
MAX
, unless otherwise noted.)
Parameter Min Typ Max Unit Test Conditions/Comments
POWER SUPPLY
Supply Voltage, V
DD
3.0 3.30 5.5 V
Average Operating Supply Current, I
CC
170 215 µA 0.0625 Conversions/Sec Rate
1
5.5 10 µA Standby Mode
Undervoltage Lockout Threshold 2.35 2.55 2.8 V V
DD
Input, Disables ADC, Rising Edge
Power-On Reset Threshold 1 2.4 V
TEMPERATURE-TO-DIGITAL CONVERTER
Local Sensor Accuracy ±1 ±3 °C 0
≤
T
A
≤
100°C, V
CC
= 3 V to 3.6 V
Resolution 1 °C
Remote Diode Sensor Accuracy ±1 °C 60°C
≤
T
D
≤
100°C, V
CC
= 3 V to 3.6 V
±3 °C 0°C
≤
T
D
≤
120°C
Resolution 0.125 °C
Remote Sensor Source Current 230 µA High Level
2
13 µA Low Level
2
Conversion Time 35.7 142.8 ms From Stop Bit to Conversion Complete
(Both Channels) One-Shot Mode with
Averaging Switched On
5.7 22.8 ms One-Shot Mode with Averaging Off
(i.e., Conversion Rate = 32 or 64
Conversions per Second)
OPEN-DRAIN DIGITAL OUTPUTS
(
THERM
,
ALERT
)
Output Low Voltage, V
OL
0.4 V I
OUT
= –6.0 mA
2
High Level Output Leakage Current, I
OH
0.1 1 µA V
OUT
= V
DD
2
SERIAL BUS TIMING
2
Logic Input High Voltage, V
IH
2.1 V V
DD
= 3 V to 5.5 V
SCLK, SDATA
Logic Input Low Voltage, V
IL
0.8 V V
DD
= 3 V to 5.5 V
Hysteresis 500 mV
SCLK, SDATA
SDATA Output Low Sink Current
6 mA SDATA Forced to 0.6 V
ALERT
Output Low Sink Current 1 mA
ALERT
Forced to 0.4 V
Logic Input Current, I
IH
, I
IL
–1 +1 µA
Input Capacitance, SCLK, SDATA 5 pF
Clock Frequency 400 kHz
SMBus Timeout 25 64 ms Note 3
SCLK Clock Low Time, t
LOW
1.3 µs t
LOW
between 10% Points
SCLK Clock High Time, t
HIGH
0.6 µs t
HIGH
between 90% Points
Start Condition Setup Time, t
SU:STA
600 ns
Start Condition Hold Time, t
HD:STA
600 ns Time from 10% of SDATA to 90%
of SCLK
Stop Condition Setup Time, t
SU:STO
600 ns Time from 90% of SCLK to 10%
of SDATA
Data Valid to SCLK Rising Edge 100 ns Time for 10% or 90% of SDATA to
Time, t
SU:DAT
10% of SCLK
Data Hold Time, t
HD:DAT
300 ns
Bus Free Time, t
BUF
1.3 µs Between Start/Stop Condition
SCLK, SDATA Rise Time, t
R
300 ns
SCLK, SDATA Fall Time, t
F
300 ns
NOTES
1
See Table VI for information on other conversion rates.
2
Guaranteed by design, not production tested.
3 The SMBus timeout is a programmable feature. By default, it is not enabled. Details on how to enable it are available in the Serial Bus Interface section of this data sheet.
Specifications subject to change without notice.
FUNCTIONAL BLOCK DIAGRAM
ON-CHIP
TEMPERATURE
SENSOR
A/D
CONVERTER
BUSY RUN/STANDBY
EXTERNAL DIODE OPEN-CIRCUIT
ADDRESS POINTER
REGISTER
CONVERSION RATE
REGISTER
REMOTE TEMPERATURE
HIGH LIMIT REGISTER
CONFIGURATION
REGISTER
INTERRUPT
MASKING
LIMIT
COMPARATOR
REMOTE TEMPERATURE
VALUE REGISTER
LOCAL TEMPERATURE
VALUE REGISTER
V
DD
GND SDATA SCLK
THERM
ALERT
D+
D–
REMOTE TEMPERATURE
LOW LIMIT REGISTER
LOCAL TEMPERATURE
HIGH LIMIT REGISTER
LOCAL TEMPERATURE
LOW LIMIT REGISTER
ANALOG
MUX
ADM1032
LOCAL
THERM
LIMIT
REGISTER
EXTERNAL
THERM
LIMIT
REGISTER
DIGITAL MUX
DIGITAL MUX
STATUS REGISTER
SMBUS INTERFACE
REMOTE OFFSET
REGISTER
AN12944A-VB (PANASONIC)
2ch SPEAKER AMPLIFIER
BLOCK DIAGRAM
PIN FUNCTION DESCRIPTION
Pin No.
Pin Function
Pin No.
Pin Function
Pin name Function Pin name Function
1 MUTE L Activist the Low Mute 25 FILT3 L Filter terminal 3
2 MUTE H Activist the High Mute 26 FILT2 L Filter terminal 2
3 BIAS30 3V Bias Output 27 FILT1 L Filter terminal 1
4 EVR_VTL EVR Control Pin 28 EVROUT_L EVR Lch Output
5 SPIN R SP Amp Rch Input 29 AMP I L The amplifier input for the gain adjustment
6 AMPO R The amplifier output for the gain adjustment 30 GND GND
7 GND GND 31 AMPO L The amplifier output for the gain adjustment
8 AMP I R The amplifier input for the gain adjustment 32 SPIN_L SP Amp Lch Input
9 EVROUT_R EVR Rch Output 33 DET C AGC demodulation Pin
10 FILT1 R Filter terminal 1 34 AGC MOD AGC-ON Level Control
11 FILT2 R Filter terminal 2 35 BIAS45 4.5V Bias Output
12 FILT3 R Filter terminal 3 36 VREF SP The VREG C terminal
13 FILT SW Filter ON/OFF Control 37 GNDSP L GND SP Lch
14 STB SW Standby ON/OFF Control 38 OUT_LN2 SP Amp Lch Output (-)
15 AUDIN L Rch Input 39 OUT LN1 SP Amp Lch Output (-)
16 TC The timing condenser for Precharge 40 OUT_LP2 SP Amp Lch Output (+)
17 GND GND 41 OUT LP1 SP Amp Lch Output (+)
18 VREG C The VREG C terminal 42 VCCSP L VCC SP Lch
19 VCC VCC 43 VCCSP R VCC SP Rch
20 BEEP IN Beep Signal Input 44 OUT RP1 SP Amp Rch Output (+)
21 VREF C The VREF C terminal 45 OUT_RP2 SP Amp Rch Output (+)
22 AUDIN_L Lch Input 46 OUT RN1 SP Amp Rch Output (-)
23 BEEP ADJ Beep signal level adjustment terminal 47 OUT RN2 SP Amp Rch Output (-)
24 AGC SW AGC ON/OFF Control 48 GNDSP R GND SP Rch