background image

52

Specifications

The N-Mark is a trademark or registered trademark of 
NFC Forum, Inc. in the United States and in other 
countries.
USB Type-C

®

 and USB-C

®

 are registered trademarks of 

USB Implementers Forum.

Design and specifications are subject to change without 
notice.

Transmitter (UTX-B40/M40/P40)

Items common to all transmitters

Oscillator type Crystal-controlled PLL synthesizer
Carrier frequencies

14UC model: 470.125 MHz to 

541.875 MHz 

 

(UHF-TV channels 14 to 25)

25UC model: 536.125 MHz to 

607.875 MHz 

 

(UHF-TV channels 25 to 36)

90U model: 941.625 MHz to 

951.875 MHz, 953.000 MHz to 
956.125 MHz, and 956.625 MHz to 
959.625 MHz

21CE model: 470.025 MHz to 

542.000 MHz 

 

(UHF-TV channels 21 to 29)

33CE model: 566.025 MHz to 

630.000 MHz 

 

(UHF-TV channels 33 to 40)

42CE model: 638.025 MHz to 

694.000 MHz 

 

(UHF-TV channels 42 to 48)

42LA model: 638.125 MHz to 

697.875 MHz 

 

(UHF-TV channels 42 to 51)

29CN model: 638.025 MHz to 

694.000 MHz 

 

(UHF-TV channels 29 to 35)

KR model: 925.125 MHz to 

937.375 MHz

E model: 794.125 MHz to 805.875 MHz

Preemphasis

50 µs

Reference frequency deviation

±5 kHz (–60 dBV, 1 kHz input)

Distortion

0.9% or less (–60 dBV, 1 kHz input)

Signal-to-noise ratio

60 dB (–60 dBV, 1 kHz input)
102 dB (GAIN MODE set to AUTO 

GAIN, max.)

96 dB (GAIN MODE set to NORMAL, 

max.)

Audio delay

Approx. 0.35 ms

Tone signal frequency

In UWP-D compander mode: 

32.382 kHz

In UWP compander mode: 32 kHz
In WL800 compander mode: 

32.768 kHz

Supply voltage DC 3.0 V (two LR6/AA size alkaline 

batteries)

DC 5.0 V (supplied from USB 

connector)

NFC function

Built-in

IR SYNC function

Built-in

USB port

USB Type-C

Operating temperature

0 °C to 50 °C (32 °F to 122 °F)

Storage temperature

–20 °C to +55 °C (–4 °F to +131 °F)

When used in locations with an ambient temperature of 
45 °C (113 °F) or higher, make sure the unit does not 
come into direct contact with your skin, as it may cause 
burns due to high temperature.

Body-pack transmitter (UTX-B40)

Antenna

1/4 

λ

 wavelength wire antenna

Audio input connector

3.5-mm diameter 3-pole locking mini 

jack

Reference audio input level

–60 dBV (MIC input, GAIN MODE set 

to NORMAL, 0 dB attenuation)

+4 dBu (LINE input)

RF output level 30 mW/5 mW selectable (UC, U, CE, 

LA, CN models)

10 mW/2 mW selectable (E, KR 

models)

Frequency response

23 Hz to 18 kHz (Typical)

Attenuation

0 dB to 27 dB (3 dB steps)

Indicators

POWER, AUDIO/MUTE

Battery life (measured with two LR6/AA size alkaline 

batteries at 25 °C (77 °F), DISPLAY 
MODE set to AUTO OFF)

Approx. 8 hours with output power of 

30 mW (UC, U, CE, LA, CN 
models)

Approx. 10 hours with output power of 

10 mW (E, KR models)

Note

Содержание URX-P40

























































Отзывы: