background image

Precautions / Maintenance

10

Others

Precautions

On safety

• Check the operating voltage before operation.

Operate the unit only with a power source specified in 
“Specifications”.

• Stop operation immediately if any liquid or solid 

object falls into the cabinet. Unplug the unit and have 
it checked by qualified personnel.

• Unplug the unit from the wall outlet if you will not be 

using it for a long time. Disconnect the power cord by 
grasping the plug. Never pull the cord itself.

• Do not disassemble the cabinet. Refer servicing to 

qualified personnel only.

• Do not touch the cutting blade of the printer.
• Connect the power plug of the printer to a wall outlet 

with a protective earth terminal. The safety earth 
should be properly established.

On operation

Do not turn the power off while the printer is printing. 
The thermal head may be damaged.

On the printer carriage

Do not carry or move the printer when the paper roll is 
placed in the printer. Doing so may cause a malfunction.

On installation

• Place the printer on a level and stable surface.

If you use the printer with placed on an uneven 
surface, malfunction of the printer is likely to occur.

• Do not install the printer near heat sources. Avoid 

locations near radiators or air ducts, or places subject 
to direct sunlight or excessive dust, humidity, 
mechanical shock or vibration.

• Provide adequate air circulation to prevent heat build-

up. Do not place the printer on surfaces such as rugs, 
blankets, etc., or near materials such as curtains and 
draperies.

• If the printer is subjected to wide and sudden changes 

in temperature, such as when it is moved from a cold 
room to a warm room or when it is left in a room with 
a heater that tends to produce large amounts of 
moisture, condensation may form inside the printer.  
In such cases the printer will probably not work 
properly, and may even develop a fault if you persist in 
using it.  If moisture or condensation forms, turn off 
the power and allow the printer to stand for at least one 
hour.

Maintenance

Cleaning the Cabinet

Use a wrung out damp cloth, or a damp cloth soaked in 
water and a mild detergent, to clean the cabinet surface. 
To avoid damaging the printer cabinet, never use 
alcohol, thinner, or any other type of organic solvent, or 
any type of abrasive cleaner, to clean the printer cabinet.

Cleaning the Thermal Head

If a printout appears dirty, or if you see white stripes in 
a printout, use the cleaning sheet (provided with the 
printer) to clean the thermal head.

1

Press the power button ON/OFF switch to turn on 
the printer.

2

Press the OPEN button to open the paper door.

Содержание UP-D895MD















Отзывы: