Sony SPP-A2470 страница 63 Скачать руководство пользователя | Manualshive

Страница: 63 / 72

background image

Additional Information

63

US

Additional Information

Remedy

• Make sure you set up the base unit correctly (page 8).
• Move the handset closer to the base unit.

• Make sure the telephone line cord is securely

connected to the telephone outlet.

• Make sure the battery is fully charged (page 11).

• Make sure the dialing mode is set correctly (page 10).

• Make sure the last dialed number is really the one you

want to dial.

• The number you last dialed exceeds 32 digits

(including the tone and pause digits if used).

• The number you last dialed is erased.

• Set the RING switch on the handset to ON.
• The battery may be weak. Charge the battery for

more than 12 hours (page 11).

• Make sure you set up the base unit correctly (page 8).
• Move the handset closer to the base unit.

• Move the handset closer to the base unit.
• Place the base unit away from noise sources (page 8).
• Place the base unit so that the antenna keeps away

from metal products.

• It is an out-of-range alarm. Move the handset closer to

the base unit within one minute.

• The battery is weak. Charge the battery for more than

12 hours (page 11).

• Follow the procedure for changing the language

(page 17).

Symptom

You hear five short error
beeps when you press

(TALK)

.

You hear no dial tone.

The phone does not connect at
all, even though the number
you dial is correct.

The phone does not redial
correctly.

You hear five short error beeps
when you try to redial.

The handset does not ring.

You hear interference during
conversation.

You hear a beep every second
during conversation and “OUT
OF RANGE” appear on the
display.

You hear a beep twice per
second and

E

and “BATTERY

LOW” appear on the display.

An incorrect language is set for
the display and the voice
guidance.

Making calls

Receiving

calls

During conversation

Troubleshooting

If you’ve experienced any of the following difficulties while using your
phone, use this troubleshooting to help you remedy the problem.
Should any problem persist, consult your nearest Sony dealer.

continued

Display and the voice guidance

language

«
...
61
62
63
64
65
...
»

Содержание SPP-A2470









































































Отзывы:

Нет отзывов

Похожие инструкции для SPP-A2470

Бренд: Octopus Страницы: 122

Бренд: Aastra Страницы: 2

Бренд: Panasonic Страницы: 67

80-6115-00 - AT&T E5813B - 5.8 GHZ Three Handset Answering System

Бренд: VTech Страницы: 53

Бренд: BT Страницы: 2

Бренд: Verizon Страницы: 55

DECT2060-2 - DECT Cordless Phone

Бренд: Uniden Страницы: 56

Бренд: BT Страницы: 72

Бренд: Uniden Страницы: 24

Бренд: Xblue Networks Страницы: 121

Бренд: Uniden Страницы: 72

Бренд: VTech Страницы: 8

Бренд: Bluesim Страницы: 12

Omni Enterprise 4028

Бренд: Alcatel Страницы: 2

Бренд: Chinavision Страницы: 18

NTT DOCOMO F-01A

Бренд: Fujitsu Страницы: 21

Бренд: Fujitsu Страницы: 2

Бренд: Fujitsu Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды