Sony SLV-X9G Скачать руководство пользователя страница 49

Страница: 49 / 96

Recording TV programmes

er
a

tio

Tips

• To select a programme position, you can use the programme number buttons on the

remote commander. For two-digit numbers, press the

(ten’s digit) button

followed by the programme number buttons.

• If you connect additional equipment to a LINE connector or jack, you can select

the input signal using the INPUT SELECT or PROG +/– buttons.

• The

DISPLAY information appears on the TV screen indicating information

about the tape, but the information will not be recorded on the tape.

• If you do not want to watch TV while recording, you can turn off the TV.

Notes

• The

DISPLAY information does not appear during still (pause) mode or slow-

motion playback.

• The

DISPLAY information will not appear while playing an NTSC-recorded

tape.

• If a tape has portions recorded in both PAL and NTSC systems, the time counter

reading will not be correct. This discrepancy is due to the difference between the
counting cycles of the two video systems.

• When you insert a non-standard commercially available tape, the remaining time

may not be correct.

• The remaining time is intended for rough measurement only.
• About 30 seconds after the tape begins playback, the tape remaining time will be

displayed.

• The station name may not appear if the VCR does not receive station name

information signals.

Recording what you are watching on the TV (TV Direct
Rec)

If you use the SMARTLINK connection, you can easily record what you are
watching on the TV (other than tapes being played on the VCR).

Insert a tape with its safety tab in place.

Press

REC while you are watching a TV programme or external

source.

The VCR automatically turns on, then the TV indicator lights up and the
VCR starts recording what you are watching on the TV.

continued

Содержание SLV-X9G

































































































Результаты поиска

Содержание SLV-X9G

Отзывы:

Похожие инструкции для SLV-X9G

Бренды по названию

Популярные бренды

Sony SLV-X9G, Руководство по эксплуатации

Результаты поиска

Содержание SLV-X9G

Отзывы:

Похожие инструкции для SLV-X9G

Бренды по названию

Популярные бренды