Sony SAITe1300-F страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 50

background image

33

Chapter 3 Operation

Turning Off the Unit

1

Press the DOOR button to unlock and open the front door.

2

Press the power switch on the front panel.

Caution

Do not turn off the S-AIT Tape Drive Unit when it is in use or there is a cartridge
in the unit, as this could damage data.

Note

After turning off the S-AIT Tape Drive Unit, wait at least 10 seconds before
turning it on again.

Preparing Cartridges

Make sure that cartridges are not write-protected and prepare them for use.
Verify whether the write-protect switch is in the write-enable position. For
details, see “Setting the Write-protect Switch” on page 38.

Inserting a Cartridge

1

Press the DOOR button to unlock and open the front door.

2

Press the power switch on the front panel.

The POWER indicator lights green and the TAPE MOTION, DRIVE
ERROR, TAPE ERROR and CLEANING REQUEST indicators flash as
the unit performs a self-diagnostic.

3

When the four indicators go out, insert your cartridge.

If the indicators do not go out, see chapter 1 or try the troubleshooting
procedures in the appendix to determine the problem.

«
...
31
32
33
34
35
...
»

Содержание SAITe1300-F



















































Отзывы:

Нет отзывов

Похожие инструкции для SAITe1300-F

Бренд: PARYA Страницы: 6

Бренд: Thecus Страницы: 120

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

Mobile Wi-Fi Pocket Drive

Бренд: Macally Страницы: 71

FlashPen USB 2.0 Piko Business

Бренд: Hama Страницы: 4

Бренд: Alphacool Страницы: 2

Бренд: Western Digital Страницы: 2

storagetek sl150

Бренд: Oracle Страницы: 196

Бренд: Home Decorators Collection Страницы: 5

Бренд: Clarke Страницы: 2

Бренд: nimble Страницы: 10

SteelVine SiI 4726

Бренд: Silicon Image Страницы: 2

Бренд: Silicon Graphics Страницы: 22

Бренд: QNAP Страницы: 41

Cheetah T10 SAS ST3146755SS

Бренд: Seagate Страницы: 88

Mobile SSD Secure

Бренд: LaCie Страницы: 18

Бренд: Faller Страницы: 4

Бренд: SanDisk Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды