Sony SAITe1300-F страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 50

background image

26

Chapter 2 Installation

Connecting the Power Cable

1

Verify the power cable plug to make sure that it matches the AC IN
connector receptacle.

2

Make sure that the electrical outlet you use to connect the unit is properly
grounded.

3

Connect one end of the power cable to the AC IN connector and the other
end to the power outlet.

Note

If the S-AIT drive does not come with a power cable, make sure that you
connect a power cable appropriate for your country to this connector.

Installing Device Drivers

A device driver is host firmware that allows the S-AIT Tape Drive Unit to
interact with a variety of hosts.

If your software requires it, install the appropriate device driver for your system
from the supplied CD-ROM. Refer to the instructions on the CD-ROM to install
device drivers.

The latest device drivers and documentation for the S-AIT Tape Drive Units are
available online. Contact your dealer for details or visit the Sony Web site
(http://www.sony.net/Products/storagesolution/).

If you are using a SAITe1300-S (SCSI model), proceed to “Connecting the
SCSI Bus Cable (SAITe1300-S only)” on page 27.
If you are using a SAITe1300-F (Fibre Channel interface model), proceed to
“Connecting the Optical Fiber Cable for Fibre Channel (SAITe1300-F only)”
on page 29.

AC Power

«
...
24
25
26
27
28
...
»

Содержание SAITe1300-F



















































Отзывы:

Нет отзывов

Похожие инструкции для SAITe1300-F

Бренд: WATSON Страницы: 12

Бренд: Campbell Страницы: 46

Бренд: IBM Страницы: 2

A16F-R2431 Galaxy Raid

Бренд: Rorke Data Страницы: 110

Бренд: Iomega Страницы: 36

Бренд: Sans Digital Страницы: 2

Бренд: Seville Classics Страницы: 7

TS7650 PROTECTIER DEDUPLICATION APPLIANCE

Бренд: IBM Страницы: 218

Universal Working Table WT 840

Бренд: Elektra Beckum Страницы: 4

Бренд: INTILION Страницы: 121

Бренд: Hama Страницы: 5

Бренд: Weka Страницы: 20

Бренд: Mcombo Страницы: 11

WALLFIX STORAGE BOX

Бренд: Brabantia Страницы: 2

Бренд: Marvin Test Solutions Страницы: 50

Бренд: Alpha ESS Страницы: 74

VALUE CLASSIC 16653-G

Бренд: Heartland Страницы: 60

Бренд: Holzstar Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды