Adjustment Using the Menus
23
USER CONFIG menu
The USER CONFIG menu is used for setting the
system, marker, multi display, function button, closed
caption, audio and option.
SYSTEM SETTING
PICTURE CONTROL
Adjusts to monitor the picture more
clearly.
•
SIZE H
: Adjusts the horizontal
size of the picture. The
higher the setting, the larger
the horizontal size of the
picture. The lower the
setting, the smaller the
horizontal size of the
picture.
•
SIZE V
: Adjusts the vertical size
of the picture. The higher
the setting, the larger the
vertical size of the picture.
The lower the setting, the
smaller the vertical size of
the picture.
•
SHIFT H
: Adjusts the position of
the picture. As the setting
increases, the picture moves
to the right, and as the
setting decreases, the picture
moves to the left.
•
SHIFT V:
Adjusts the position of
the picture. As the setting
increases, the picture moves
up, and as the setting
decreases, the picture moves
down.
•
DOT PHASE
: Adjusts the dot
phase. Adjust the picture
further for a finer picture
after APA (page 27) is
adjusted.
•
PITCH:
Adjusts the horizontal
size of the picture with the
left side of the picture fixed.
The higher the setting, the
larger the width of the
picture. The lower the
setting, the narrower the
width of the picture.
•
RESOLUTION:
Sets when the
computer signal is input and
it is difficult to understand
the signal type such as
XGA/60, WXGA/60,
UXGA/60 or WUXGA/60.
•
XGA:
Displayed as XGA
signal.
•
WXGA:
Displayed as
WXGA signal.
•
UXGA:
Displayed as
UXGA signal.
•
WUXGA:
Displayed as
WUXGA signal.
•
RESET:
Resets the value of
SIZE H, SIZE V, SHIFT H,
SHIFT V, DOT PHASE and
PITCH to the factory preset
value.
Submenu
Setting
Submenu
Setting
MATRIX
Applied to 480/60I or 480/60P
signal. Select 601 or 709.
COMPONENT LEVEL
Selects the component level from
among three modes.
•
SMPTE:
for 100/0/100/0 signal
•
BETA0:
for 100/0/75/0 signal
•
BETA7.5:
for 100/7.5/75/7.5
signal
NTSC SETUP
Selects the NTSC setup level from
two modes.
The 7.5 setup level is used mainly
in North America. The 0 setup level
is used mainly in Japan.
SCAN
Enables setting of the scan mode by
the button which the scan function
is assigned. Select from among
“STANDARD” and
“FULL+NATIVE”. The displayed
picture differs according to the
selected mode (see “Scan mode
image” on page 24).
When STANDARD is selected
NORMAL scan (0% scan) and
OVER scan (5% over scan)
When FULL+NATIVE is selected
NORMAL scan, OVER scan,
FULL screen and NATIVE (1080i
and 720P only)
S Y S T E M S E T T I N G :
M A R K E R S E T T I N G :
M U LT I D I S P L AY S E T T I N G :
F U N C T I O N B U T T O N S E T T I N G :
C L O S E D C A P T I O N S E T T I N G :
A U D I O S E T T I N G :
O P T I O N S E T T I N G :
USER CONFIG
M AT R I X :
xxx
C O M P O N E N T L E V E L :
xxxxx
N T S C S E T U P :
x
S C A N :
xxxxxx
F O R M AT D I S P L AY:
xx
L A N G U A G E : E N G L I S H
P O W E R S AV I N G :
xx
I / P M O D E :
xxxxxxx
B A C K G R O U N D :
x
USER CONFIG – SYSTEM SETTING
