2-9
NEX-FS700/FS700K/FS700C/FS700CK/FS700E/FS700EK/FS700J/FS700JK/FS700R/FS700RH/FS700U/FS700UK
2-1-7. MOUNT BLOCK SECTION
ns : not supplied
Screw
301
A-1885-380-A SERVICE, MOUNT BLOCK ASSY (_)
(including IC9001 (CMOS imager) and IS-102 board) (Note5)
302
4-269-054-01
MB N PLATE (A (945))
*
303
4-185-963-01
MB N PLATE SP (Note 4)
304
4-425-279-01
RING (960), LENS
305
4-299-974-01
BUTTON, L LOCK
306
X-2582-840-1 PIN ASSY, L LOCK
307
4-257-700-01
SPRING, LOCK (L)
308
4-425-282-01
CABINET, MT INNER
309
A-1876-371-B MB CONTACT UNIT (755), N
310
A-1885-295-A MT-076 BOARD, COMPLETE
311
4-424-696-01
MB SHEET (960), MASK
312
A-1889-736-A NDF UNIT SERVICE (Note 6)
313
4-424-716-01
MB RUBBER (SG), SEAL
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
*
314
Selection Parts IM WASHER (A), ADJUST (Note 1, 2)
315
1-968-297-11
HARNESS (COAXIAL CABLE)
316
3-079-115-01 TAPE
AS
317
4-425-280-01
HEAT SINK, MT
318
2-590-635-01
TAPE (AS 1/2)
319
4-408-292-01
SHEET, CM RADIATION (Note 3)
320
4-188-536-01 CAP,
BODY
321
4-441-046-01 SPACER,
ND
#11
3-078-890-11 SCREW,
TAPPING
#49
2-630-005-31
SCREW (M2), NEW TRUSTER, P2
#50
2-891-494-11
SCREW (M2), NEW TRUSTER, P2
#69
2-599-475-21 SCREW
(M1.7)
#234
4-186-545-11
SCREW, 0+Z M1.7 SG (SPIN)
#271
3-270-483-01
GRIP, (M1.7 X 4.0) (2 MAIN EG)
Note
Note 1:
The IM adjust washers (A) differ in thickness.
Make sure to return the removed IM adjust washers to
original places.
When replacing IM adjust washers, refer to "SELECTION
PARTS".
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Mount Block Assy
(Service).
Note 1:
IM
調整ワッシャ
(A)
は，それぞれ厚さが異なります。
取り外した
IM
調整ワッシャは，必ず元の位置に戻してく
ださい。
また，
IM
調整ワッシャを交換する際は，
“SELECTION
PARTS”
を参照してください。
IM adjust washer
を紛失するなどして元の状態に戻せな
くなった場合は，
Mount Block Assy (Service)
を交換し
てください。
Refer to “Assembly-4: Putting position of the IM Adjust
Washer (A).”.
“Assembly-4: Putting position of the IM Adjust Washer
(A).”
Refer to “Assembly-5: Attaching method of the CM Radiation
Sheets.”.
“Assembly-5: Attaching method of the CM RadiationSheets.”
Note 5:
Precautions for Replacement of the Mount Block Assy
Service
As Mount Block Assy Service may be damaged by static
electricity from its structure, handle it carefully like for the
MOS IC.
In addition, ensure that the receiver is not covered with dust
nor exposed to strong light.
Note 5:
マウントブロック
Assy
サービス交換時の注意
マウントブロック
Assy
サービスは構造上，静電気によ
り破壊される恐れがあるため，
MOS IC
と同様に注意し
て取り扱ってください。
また，受光部にはゴミの付着，および強い光がはいるこ
とのないように注意してください。
320
302
312
(Note 6)
313
315
303
(Note 4)
304
321
308
309
310
305
306
#50
ns
ns
#50
#49
#49
#234
#69
#271
#11
#271
A
A
ns
307
311
317
316
314
(Note1, 2)
314
(Note1, 2)
319
(Note 3)
318
315
316
301
(including IC9001 (CMOS imager) and IS-102 board)
(Note 5)
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
3.0
2.0
#271: M1.7 X 4.0
(Black)
3-270-483-01
4.0
1.7
Refer to "Assembly-6: Apply grease on the MB N Plate SP.
“Assembly-6: Apply grease on the MB N Plate SP.”
#69: M1.7 X 3.0
(Silver)
2-599-475-21
3.0
1.7
#234:
5.5
1.7
M1.7 X 5.5
(Silver)
4-186-545-11
Note 6:
New NDF Unit Service is attached two Protection Sheets
When assemble this part, peel off two sheets.
Note 6:
新品の
NDF Unit Service
には
Protection Sheet
が
2
枚貼り
付けられています。
取付時はこれらのシートを剥がしてください。
SELECTION PARTS
Ref. No.314
Select the optimum thickness of washer.
* 4-185-995-01 IM WASHER (A), ADJUST (t = 0.05)
* 4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
* 4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
* 4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
* 4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
* 4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
* 4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
* 4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
* 4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
* 4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
